U-Boot

仕方がないので、
SheevaPlug の電源を入れ、
USB デバイスが認識されるプポーンという音がしたら すぐに Teraterm を起動し、
Enter を何度か押すと、U-Boot のプロンプトになった。

512 MB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0
Marvell>>
Marvell>>

version

Marvell>> version

U-Boot 1.1.4 (Mar 19 2009 - 16:06:59) Marvell version: 3.4.16
Marvell>>

help

Marvell>> help
?       - alias for 'help'
base    - print or set address offset
boot    - boot default, i.e., run 'bootcmd'
bootd   - boot default, i.e., run 'bootcmd'
bootext2    dev:boot_part1,boot_part2 addr boot_image linux_dev_name
bootm   - boot application image from memory
bootp   - boot image via network using BootP/TFTP protocol
bubt    - Burn an image on the Boot Nand Flash.
chpart  - change active partition
cmp     - memory compare
cmpm    - Compare Memory
cp      - memory copy
cpumap - Display CPU memory mapping settings.
crc32   - checksum calculation
date    - get/set/reset date & time
dclk    - Display the MV device CLKs.
dhcp    - invoke DHCP client to obtain IP/boot params
diskboot- boot from IDE device
echo    - echo args to console
eeprom  - EEPROM sub-system
erase   - erase FLASH memory
ext2load- load binary file from a Ext2 filesystem
ext2ls  - list files in a directory (default /)
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
fi      - Find value in the memory.
flinfo  - print FLASH memory information
fsinfo  - print information about filesystems
fsload  - load binary file from a filesystem image
g       - start application at cached address 'addr'(default addr 0x40000)
go      - start application at address 'addr'
help    - print online help
icrc32  - checksum calculation
ide     - IDE sub-system
iloop   - infinite loop on address range
imd     - i2c memory display
imm[.b, .s, .w, .l]     - i2c memory modify (auto-incrementing)
imw     - memory write (fill)
inm     - memory modify (constant address)
iprobe  - probe to discover valid I2C chip addresses
ir      - reading and changing MV internal register values.
loop    - infinite loop on address range
ls      - list files in a directory (default /)
map     - Diasplay address decode windows
md      - memory display
me      - PCI master enable
mm      - memory modify (auto-incrementing)
mp      - map PCI BAR
mtdparts- define flash/nand partitions
mtest   - simple RAM test
mv_diag - perform board diagnostics
mv_diag
        - display all available tests
mv_diag all
        - run all available tests
mv_diag test1
        - run specified test
mw      - memory write (fill)
nand                   - NAND sub-system
nboot   - boot from NAND device
nbubt   - Burn a boot loader image on the Boot Nand Flash.
nm      - memory modify (constant address)
pci     - list and access PCI Configuration Space
phyRead - Read PCI-E Phy register
pciePhyWrite    - Write PCI-E Phy register
phyRead - Read Phy register
phyWrite        - Write Phy register
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
rcvr    - Satrt recovery process (Distress Beacon with TFTP server)
reset   - Perform RESET of the CPU
resetenv        - Return all environment variable to default.
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
se      - PCI Slave enable
setenv  - set environment variables
sflash  - read, write or erase the external SPI Flash.
sg      - scanning the PHYs status
sp      - Scan PCI bus.
tftpboot- boot image via network using TFTP protocol
usb     - USB sub-system
usbboot - boot from USB device
version - print monitor version
Marvell>>

printenv

Marvell>> printenv
baudrate=115200
loads_echo=0
rootpath=/mnt/ARM_FS/
netmask=255.255.0.0
console=console=ttyS0,115200
CASset=min
MALLOC_len=1
ethprime=egiga0
bootargs_root=root=/dev/mtdblock2 ro
ethmtu=1500
usb0Mode=host
nandEcc=1bit
ethact=egiga0
serverip=10.10.0.2
ipaddr=10.10.0.1
cesvcid=ULULULULULULPPULULULULULDA
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
ethaddr=00:50:43:01:CA:72
run_diag=no
bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs) rw root=/dev/mtdblock1 rw ip=10.4.50.4:10.4.50.5:10.4.50.5:255.255.255.0:DB88FXX81:eth0:none
bootcmd=nand read.e 0x800000 0x100000 0x400000; bootm 0x800000
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes

Environment size: 1304/131068 bytes
Marvell>>