U-Boot

HS-DHGL KURO-BOX/Pro KURO-NAS/X4 LS-CL LS-GL LS-HGL LS-LGL LS-QL LS-SL LS-WSGL

U-Boot

LS-HGL の例

Orion1   CPU =  Low

Checking DATA BUS
Checking ADDRESS BUS

> Checking hardware info ...
=== Strap status : 0x00800030 ===
=== H/W boardId  :       0x23 ===
=== boardId      :       0x1b ===
=== micon_support:        off ===
> OK.
=== BUFFALO LS-HGL U-Boot. ===
 ** LOADER **
 ** BUFFALO BOARD: BUFFALO_BOARD_LS_HGL LE (CFG_ENV_ADDR=fffff000)


U-Boot 1.1.1 (May 27 2008 - 19:18:26) Marvell version: 1.12.1 - TINY
Buffalo Version: 1.17-1.00

DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done

Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
Orion 1 streaming disabled
SysClock = 250Mhz , TClock = 166Mhz


USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net:   egiga0 [PRIME]
Using 88E1118 phy
buffalo_change_power_status > Read 0x5c
buffalo_IsStopAtUbootStatus > MagicKey=0x5c
buffalo_change_power_status > Read 0x5c
buffalo_change_power_status > Read 0x5c
buffalo_change_power_status > Writing 0x5c

Please Press HDD power button to continue ...
buffalo_change_power_status > Read 0x5c
buffalo_change_power_status > Writing 0x3a

Marvell Serial ATA Adapter
Integrated Sata device found
  Device 0: OK
Model: ST3250823AS                              Firm: 3.02     Ser#:             3ND06QAZ
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)

Using device ide0, partition 1

Loading from block device ide device 0, partition 1: Name: hda1
  Type: U-Boot  File:/uImage.buffalo

1715900 bytes read
   Image Name:   Linux-2.6.16.16-arm1
   Created:      2008-12-27   4:21:16 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1715836 Bytes =  1.6 MB
   Load Address: 00008000
   Entry Point:  00008000
Using device ide0, partition 1

Loading from block device ide device 0, partition 1: Name: hda1
  Type: U-Boot  File:/initrd.buffalo

5950179 bytes read
   Image Name:   initrd
   Created:      2008-12-30   8:51:11 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    5950115 Bytes =  5.7 MB
   Load Address: 00000000
   Entry Point:  00000000
Using device ide1, partition 1
** Bad partition 1 **
serch_boot_drv (185)>No kernel_file 1
Using device ide1, partition 1
** Bad partition 1 **
serch_boot_drv (240)>No init_file 1
Booting from Device 0
hit any key to switch tftp boot.
Hit any key to stop autoboot:  0
Hit any key to stop autoboot:  0

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
  Device 0: OK
Model: ST3250823AS                              Firm: 3.02     Ser#:             3ND06QAZ
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)

Using device ide0, partition 1

Loading from block device ide device 0, partition 1: Name: hda1
  Type: U-Boot  File:/uImage.buffalo

1715900 bytes read
Using device ide1, partition 1
** Bad partition 1 **
## Booting image at 00100000 ...
   Image Name:   Linux-2.6.16.16-arm1
   Created:      2008-12-27   4:21:16 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1715836 Bytes =  1.6 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00800000 ...
   Image Name:   initrd
   Created:      2008-12-30   8:51:11 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    5950115 Bytes =  5.7 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...