U-Boot のコマンドモード

HS-DHGL KURO-BOX/Pro KURO-NAS/X4 LS-CL LS-GL LS-HGL LS-LGL LS-QL LS-SL LS-WSGL

コマンドモード

U-Boot のコマンドモードに入るには、２回目のカウントダウンで何かキーを押せば良い。

Orion1   CPU =  Low

Checking DATA BUS
Checking ADDRESS BUS

> Checking hardware info ...
=== Strap status : 0x00800030 ===
=== H/W boardId  :       0x23 ===
=== boardId      :       0x1b ===
=== micon_support:        off ===
> OK.
=== BUFFALO LS-HGL U-Boot. ===
 ** LOADER **
 ** BUFFALO BOARD: BUFFALO_BOARD_LS_HGL LE (CFG_ENV_ADDR=fffff000)


U-Boot 1.1.1 (May 27 2008 - 19:18:26) Marvell version: 1.12.1 - TINY
Buffalo Version: 1.17-1.00

DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done

Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
Orion 1 streaming disabled
SysClock = 250Mhz , TClock = 166Mhz


USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net:   egiga0 [PRIME]
Using 88E1118 phy
buffalo_change_power_status > Read 0x2b
buffalo_IsStopAtUbootStatus > MagicKey=0x2b
buffalo_change_power_status > Read 0x2b
buffalo_change_power_status > Read 0x2b
buffalo_change_power_status > Writing 0x5c

Please Press HDD power button to continue ...
buffalo_change_power_status > Read 0x5c
buffalo_change_power_status > Writing 0x3a

Marvell Serial ATA Adapter
Integrated Sata device found
  Device 0: OK
Model: ST3250823AS                              Firm: 3.02     Ser#:             3ND06QAZ
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)

Using device ide0, partition 1

Loading from block device ide device 0, partition 1: Name: hda1
  Type: U-Boot  File:/uImage.buffalo

1715900 bytes read
   Image Name:   Linux-2.6.16.16-arm1
   Created:      2008-12-27   4:21:16 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1715836 Bytes =  1.6 MB
   Load Address: 00008000
   Entry Point:  00008000
Using device ide0, partition 1

Loading from block device ide device 0, partition 1: Name: hda1
  Type: U-Boot  File:/initrd.buffalo

5950179 bytes read
   Image Name:   initrd
   Created:      2008-12-30   8:51:11 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    5950115 Bytes =  5.7 MB
   Load Address: 00000000
   Entry Point:  00000000
Using device ide1, partition 1
** Bad partition 1 **
serch_boot_drv (185)>No kernel_file 1
Using device ide1, partition 1
** Bad partition 1 **
serch_boot_drv (240)>No init_file 1
Booting from Device 0
hit any key to switch tftp boot.
Hit any key to stop autoboot:  0
Hit any key to stop autoboot:  3 ← ここが 0 になる前に何かキーを押す
Marvell>>

コマンドモードのヘルプ

Marvell>> help
?       - alias for 'help'
base    - print or set address offset
board_info   -show board information.
boot    - boot default, i.e., run 'bootcmd'
bootd   - boot default, i.e., run 'bootcmd'
bootend - with micon. send bootend.
bootm   - boot application image from memory
bootp   - boot image via network using BootP/TFTP protocol
bubt    - Burn an image on the Boot Flash.
buzzer          - with micon. buzzer command.
cmp     - memory compare
cp      - memory copy
cpumap - Display CPU memory mapping settings.
crc32   - checksum calculation
date    - get/set/reset date & time
diskboot- boot from IDE device
echo    - echo args to console
erase   - erase FLASH memory
ext2load- load binary file from a Ext2 filesystem
ext2ls- list files in a directory (default /)
fan_control     - with micon. fan control  .
fan_rpm         - with micon. fan get rpm.
flinfo  - print FLASH memory information
get_sw          - without micon. get switch status.
go      - start application at address 'addr'
hdd_power       - hdd power control  .
help    - print online help
ide     - IDE sub-system
led             - without micon. call led control routine(for debug).
led_blink       - with micon. led blink control setting.
led_cpu_mcon    - with micon. led cpu micon control setting.
led_on_off      - with micon. led on off control setting.
loop    - infinite loop on address range
md      - memory display
micon           - with micon. command(2byte hex) -data(witin 32byte hex)
mm      - memory modify (auto-incrementing)
mtest   - simple RAM test
mw      - memory write (fill)
nm      - memory modify (constant address)
pci     - list and access PCI Configuraton Space
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
resetenv        - Return all environment variable to default.
saveenv - save environment variables to persistent storage
setenv  - set environment variables
shutdown        - with micon. Poff .
sw_power        - with micon. software power control interface
tftpboot- boot image via network using TFTP protocol
usb_power       - without micon. usb power control  .
version - print monitor version
Marvell>>

Marvell>> help setenv
setenv name value ...
    - set environment variable 'name' to 'value ...'
setenv name
    - delete environment variable 'name'

Marvell>>