ハックキットで起動

HDD の交換（LS-WSGL, LS-QL 以外）

起動

	:
	:
Uncompressing Linux...................................................................................................................................... done, booting the kernel.
Linux version 2.6.22.7-88f5182 (root@build2.dd-hot24.nas.buffalo.local) (gcc version 4.2.0 20070413 (prerelease)) #1 Wed Nov 6 14:43:54 JST 2013
CPU: ARM926EJ-S [41069260] revision 0 (ARMv5TEJ), cr=a0053177
Machine: Feroceon
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Built 1 zonelists.  Total pages: 32512
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 func=0 BOOTVER=1.23
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 110108KB available (3860K code, 294K data, 120K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
env_format_version = 0x00000006
product_id = 0x00000013
Sys Clk = 200000000, Tclk = 166664740

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 128MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size   1MB
PCI0_MEM ....base e8000000, size 128MB
PCI0_IO ....base f2100000, size   1MB
INTER_REGS ....base f1000000, size   1MB
DEVICE_CS0 ....no such
DEVICE_CS1 ....base f4000000, size  32MB
DEVICE_CS2 ....no such
DEV_BOOCS ....base ff800000, size   8MB
CRYPT_ENG ....base f0000000, size  64KB

  Marvell Development Board (LSP Version 3.0.5_NAS_GDP_p8)-- BUFFALO_BOARD  Soc: 88F5182 A2

 Detected Tclk 166664740 and SysClk 200000000
Marvell USB EHCI Host controller #0: c055b600
Marvell USB EHCI Host controller #1: c055b400
IO Request resource failed - Pci If 0
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
Time: orion_clocksource clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 15360K
RTC registered
mvCesaInit: sessions=640, queue=64, pSram=f0000000
Use the XOR engines (acceleration) for enhancing the following functions:
  o RAID 5 Xor calculation
  o kernel memcpy
  o kenrel memzero
  o copy user to/from kernel buffers
Number of XOR engines to use: 2
Use IDMA channels 2 and 3 for enhancing the following function:
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
fuse init (API version 7.8)
SGI XFS with ACLs, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
io scheduler noop registered (default)
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A
serial8250.0: ttyS2 at MMIO 0xf1012100 (irq = 4) is a 16550A
RAMDISK driver initialized: 3 RAM disks of 32768K size 1024 blocksize
loop: module loaded
Marvell Ethernet Driver 'mv_ethernet':
  o Uncached descriptors in DRAM
  o DRAM SW cache-coherency
  o TCP segmentation offload enabled
  o Checksum offload enabled
  o Rx desc: 128
  o Tx desc: 256
  o Loading network interface ** eth_init_module (0)
'eth0'
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
scsi 0:0:0:0: Direct-Access     MARSHAL  MAL2160SA-T72    LH01 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
 sda: sda1 sda2 sda3 sda4 sda5 sda6
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
physmap platform flash device: 01000000 at f0000000
physmap-flash physmap-flash.0: map_probe failed
Found: SST 39LF020
cfi_flash_0: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
mice: PS/2 mouse device common for all mice
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid6: int32x1     20 MB/s
raid6: int32x2     28 MB/s
raid6: int32x4     35 MB/s
raid6: int32x8     31 MB/s
raid6: using algorithm int32x4 (35 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: measuring checksumming speed
   arm4regs  :   292.400 MB/sec
   8regs     :   242.400 MB/sec
   32regs    :   261.600 MB/sec
raid5: using function: arm4regs (292.400 MB/sec)
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Buffalo CPU Inerupts Driver (C) BUFFALO INC. Ver.0.01 alpha1 installed.
Buffalo Gpio Control Driver (C) BUFFALO INC. Ver.0.02 installed.
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
---- in hackkit linuxrc ---
grep: /var/tmp/devlink: No such file or directory
-- rebuild mdadm.conf for BOOT, ROOTFS --
mdadm: cannot open /dev/disk2_1: No such device or address
mdadm: cannot open /dev/disk2_2: No such device or address
mdadm: cannot open /dev/disk2_5: No such device or address
md: md10 stopped.
md: bind<sda5>
raid1: raid set md10 active with 1 out of 2 mirrors
mdadm: /dev/md/10 has been started with 1 drive (out of 2).
md: md1 stopped.
md: bind<sda2>
md: md1: raid array is not clean -- starting background reconstruction
raid1: raid set md1 active with 1 out of 2 mirrors
mdadm: /dev/md/1 has been started with 1 drive (out of 2).
md: md0 stopped.
md: bind<sda1>
raid1: raid set md0 active with 1 out of 2 mirrors
mdadm: /dev/md0 has been started with 1 drive (out of 2).
-- setup max error counts --
/sys/block/md0/md/maxerr_cnt is setted to -1
/sys/block/md1/md/maxerr_cnt is setted to -1
/sys/block/md10/md/maxerr_cnt is setted to -1
umount: cannot open /proc/mounts
kjournald starting.  Commit interval 5 seconds
EXT3 FS on md1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem).
Trying to move old root to /initrd ... okay
Freeing init memory: 120K
FATAL: kernel toKernel panic - not syncing: Attempted to kill init!
o old
Rebooting in 5 seconds..Reseting !!

2.6.22.7 では、もう動かんのか？？

LS-SL 楽天市場