initrd.img を unzip して initrd.buffalo を取り出す
ファンクションキーを押す
func switch pushed, and exited loop
wait until func switch released.
Marvell Serial ATA Adapter
Integrated Sata device found
** Bad partition 1 **
serch_boot_drv (194)>No kernel_file 0
** Bad partition 1 **
serch_boot_drv (249)>No init_file 0
** Bad partition 1 **
serch_boot_drv (194)>No kernel_file 1
** Bad partition 1 **
serch_boot_drv (249)>No init_file 1
hit any key to switch tftp boot.
Hit any key to stop autoboot: 0
Using egiga0 device
TFTP from server 192.168.11.1; our IP address is 192.168.11.150
Filename 'uImage.buffalo'.
Load address: 0x100000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#########################
done
Bytes transferred = 2120012 (20594c hex)
Using egiga0 device
TFTP from server 192.168.11.1; our IP address is 192.168.11.150
Filename 'initrd.buffalo'.
Load address: 0x800000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
########################################################
done
Bytes transferred = 8937716 (8860f4 hex)
## Booting image at 00100000 ...
Image Name: Linux-2.6.22.7
Created: 2009-06-14 13:44:50 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2119948 Bytes = 2 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00800000 ...
Image Name: initrd
Created: 2009-06-14 13:46:10 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 8937652 Bytes = 8.5 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
arg:console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.23 tftpboot=yes
CONFIG_BUFFALO_PLATFORM ---
Uncompressing Linux..................................................................................................................................... done, booting the kernel.
Linux version 2.6.22.7 (root@build2.dd-hot24.nas.buffalo.local) (gcc version 4.2.0 20070413 (prerelease)) #436 Sun Jun 14 22:44:37 JST 2009
キター！！
CPU: ARM926EJ-S [41069260] revision 0 (ARMv5TEJ), cr=a0053177
Machine: Feroceon
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Built 1 zonelists. Total pages: 32512
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.23 tftpboot=yes
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 110136KB available (3832K code, 294K data, 120K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
env_format_version = 0x00000006
product_id = 0x00000013
Sys Clk = 200000000, Tclk = 166664740
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 128MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
PCI0_MEM ....base e8000000, size 128MB
PCI0_IO ....base f2100000, size 1MB
INTER_REGS ....base f1000000, size 1MB
DEVICE_CS0 ....no such
DEVICE_CS1 ....base f4000000, size 32MB
DEVICE_CS2 ....no such
DEV_BOOCS ....base ff800000, size 8MB
CRYPT_ENG ....base f0000000, size 64KB
Marvell Development Board (LSP Version 3.0.5_NAS_GDP_p8)-- BUFFALO_BOARD Soc: 88F5182 A2
Detected Tclk 166664740 and SysClk 200000000
Marvell USB EHCI Host controller #0: c055b600
Marvell USB EHCI Host controller #1: c055b400
IO Request resource failed - Pci If 0
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
Time: orion_clocksource clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 15360K
RTC registered
mvCesaInit: sessions=640, queue=64, pSram=f0000000
Use the XOR engines (acceleration) for enhancing the following functions:
o RAID 5 Xor calculation
o kernel memcpy
o kenrel memzero
o copy user to/from kernel buffers
Number of XOR engines to use: 2
Use IDMA channels 2 and 3 for enhancing the following function:
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SGI XFS with ACLs, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
io scheduler noop registered (default)
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A
serial8250.0: ttyS2 at MMIO 0xf1012100 (irq = 4) is a 16550A
RAMDISK driver initialized: 3 RAM disks of 32768K size 1024 blocksize
loop: module loaded
Marvell Ethernet Driver 'mv_ethernet':
o Uncached descriptors in DRAM
o DRAM SW cache-coherency
o TCP segmentation offload enabled
o Checksum offload enabled
o Rx desc: 128
o Tx desc: 256
o Loading network interface ** eth_init_module (0)
'eth0'
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
scsi 0:0:0:0: Direct-Access Seagate ST9100828AS 3.BH PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
physmap platform flash device: 01000000 at f0000000
physmap-flash physmap-flash.0: map_probe failed
Found: SST 39LF020
cfi_flash_0: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
mice: PS/2 mouse device common for all mice
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid6: int32x1 20 MB/s
raid6: int32x2 28 MB/s
raid6: int32x4 35 MB/s
raid6: int32x8 31 MB/s
raid6: using algorithm int32x4 (35 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: measuring checksumming speed
arm4regs : 304.000 MB/sec
8regs : 248.800 MB/sec
32regs : 270.400 MB/sec
raid5: using function: arm4regs (304.000 MB/sec)
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Buffalo CPU Inerupts Driver (C) BUFFALO INC. Ver.0.01 alpha1 installed.
Buffalo Gpio Control Driver (C) BUFFALO INC. Ver.0.02 installed.
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
---- in linuxrc ---
Version 1.00 2008/ 7/ 1
Thu Nov 1 00:05:12 JST 2007
CheckDevices
grep: /var/tmp/devlink: No such file or directory
linuxrc:choose operation (timeout 4[s])
1:RamRoot other:HddRoot ? -HddRoot-
Starting :fsck_disks(boot) ... [Failed. ]
Starting :fsck_disks(rootfs) ... [Success.]
Starting :mount(boot) ... [Failed. ]
mount: mounting /dev/eth0 on /mnt failed: No such file or directory
mount: mounting /dev/eth0 on /mnt failed: No such file or directory
umount: cannot open /proc/mounts
Freeing init memory: 120K
init started: BusyBox v1.7.0 (2007-10-15 19:49:46 IST)
starting pid 333, tty '': '/etc/init.d/rcS'
--- rcStart (initrd) ---
chmod: /home: No such file or directory
grep: /var/tmp/devlink: No such file or directory
swapon: can't stat '/dev/eth0': No such file or directory
create dir : /home
create dir : /var/www
This model doesn't support raid!!!
umount: cannot umount /boot: Invalid argument
mkdir: cannot create directory '/boot': File exists
mount: mounting /dev/eth0 on /boot failed: No such file or directory
mdadm: error opening /dev/eth0: No such file or directory
mdadm: error opening /dev/eth0: No such file or directory
mdadm: error opening /dev/eth0: No such file or directory
configure files from Buffalo parameters.
mount: mounting /dev/eth0 on /boot failed: No such file or directory
Restore previous configuration files
/bin/tar: /boot/conf_save.tgz: Cannot open: No such file or directory
/bin/tar: Error is not recoverable: exiting now
/bin/tar: Child returned status 2
/bin/tar: Error exit delayed from previous errors
unzip fail.
umount: cannot umount /boot: Invalid argument
rootfs on / type rootfs (rw)
/dev/root.old on / type ext2 (rw)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
devpts on /dev/pts type devpts (rw)
/dev/ram1 on /mnt/ram type tmpfs (rw)
PID Uid VSZ Stat Command
1 root 3364 S init
2 root SW< [kthreadd]
3 root SWN [ksoftirqd/0]
4 root SW< [events/0]
5 root SW< [khelper]
32 root SW< [kblockd/0]
45 root SW [crypto]
46 root SW [crypto_ret]
49 root SW [pdflush]
50 root SW [pdflush]
51 root SW< [kswapd0]
52 root SW< [aio/0]
53 root SW< [xfslogd/0]
54 root SW< [xfsdatad/0]
242 root SW< [scsi_eh_0]
243 root SW< [scsi_eh_1]
257 root SW< [mtdblockd]
332 root 3364 S init
333 root 2448 S /bin/sh /etc/init.d/rcS
619 root 2748 R /bin/sh /etc/init.d/restore_config.sh start
635 root 3368 R ps
mv: cannot rename '/tmp/info': No such file or directory
/etc/init.d/networking.sh : Clear /etc/dhcpc/dhcpcd-eth0.pid eth0
/etc/init.d/networking.sh : Read dhcpc file eth0
/etc/init.d/networking.sh : configure : eth0
create network files.. (eth0)
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
/etc/init.d/networking.sh : Delete /etc/dhcpc/dhcpcd-eth0.pid
route: SIOCDELRT: No such process
Configuration network interface: eth0
/sbin/ifconfig eth0 mtu 1500 multicast
/etc/init.d/networking.sh: line 373: /proc/sys/net/ipv4/conf/eth1/arp_ignore: No such file or directory
requesting DHCP tout=30[s]
networking.sh: dhcp requesting...
DontDownIface
alwaysFork
eth reg(9) val=0x0300
eth0: link down
eth0: link up, full duplex, speed 1 Gbps
sendto: count 6 sync 1
sendto: count 5 sync 0
sendto: count 6 sync 0
dhcpcd.exe: interface eth0 has been configured with new IP=192.168.2.209 GATEWAY=192.168.2.96
** eth0 : networking.sh dhcp fin.
configure files from Buffalo parameters.
Starting system logger:
Starting kernel logger:
Starting kernelmon:usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_marvell ehci_marvell.4523: Marvell Orion EHCI
ehci_marvell ehci_marvell.4523: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.4523: irq 17, io base 0xf1050100
ehci_marvell ehci_marvell.4523: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_marvell ehci_marvell.167817: Marvell Orion EHCI
ehci_marvell ehci_marvell.167817: new USB bus registered, assigned bus number 2
ehci_marvell ehci_marvell.167817: irq 12, io base 0xf10a0100
ehci_marvell ehci_marvell.167817: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v3.0
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
KERNELMOn (lanact 0 half)
Starting clientUtil_server:starting on eth0
KERNELMOn (lanact 1000 full)
Starting daemonwatch:daemonwatch Ver.1.01
watch list file : /etc/daemonwatch.list
No need to run drivecheck.sh
/etc/init.d/bootcomplete.sh: line 54: /usr/local/bin/sendmail.sh: No such file or directory
/etc/init.d/networking.sh : Clear /etc/dhcpc/dhcpcd-eth0.pid eth0
/etc/init.d/networking.sh : Read dhcpc file eth0
**** request DHCP eth0
starting pid 856, tty '': '/sbin/getty'
BUFFALO INC. LinkStation series
LS-SL-EM9AF login:
「ファームウェア更新」をクリック
「はい」をクリック
がー。
LS-VL にUSB でつないで、パーティションを削除する
root@vl:~# parted -s /dev/sdb print
Model: ViPowER VP-89118(SD1) (scsi)
Disk /dev/sdb: 100GB
Sector size (logical/physical): 512B/512B
Partition Table: gpt
Number Start End Size File system Name Flags
1 17.4kB 1024MB 1024MB primary
2 1024MB 6144MB 5119MB primary
3 6144MB 7168MB 1024MB primary
4 7168MB 100GB 92.9GB primary
root@vl:~# parted -s /dev/sdb rm 4
root@vl:~# parted -s /dev/sdb rm 3
root@vl:~# parted -s /dev/sdb rm 2
root@vl:~# parted -s /dev/sdb rm 1
root@vl:~# !?print
parted -s /dev/sdb print
Model: ViPowER VP-89118(SD1) (scsi)
Disk /dev/sdb: 100GB
Sector size (logical/physical): 512B/512B
Partition Table: gpt
Number Start End Size File system Name Flags
root@vl:~# fdisk /dev/sdb
WARNING: GPT (GUID Partition Table) detected on '/dev/sdb'! The util fdisk doesn't support GPT. Use GNU Parted.
WARNING: DOS-compatible mode is deprecated. It's strongly recommended to
switch off the mode (command 'c') and change display units to
sectors (command 'u').
Command (m for help): p
Disk /dev/sdb: 100.0 GB, 100030242816 bytes
255 heads, 63 sectors/track, 12161 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000
Device Boot Start End Blocks Id System
/dev/sdb1 1 12162 97685783+ ee GPT
Command (m for help): d
Selected partition 1
Command (m for help): 1
1: unknown command
Command action
a toggle a bootable flag
b edit bsd disklabel
c toggle the dos compatibility flag
d delete a partition
l list known partition types
m print this menu
n add a new partition
o create a new empty DOS partition table
p print the partition table
q quit without saving changes
s create a new empty Sun disklabel
t change a partition's system id
u change display/entry units
v verify the partition table
w write table to disk and exit
x extra functionality (experts only)
Command (m for help): w
The partition table has been altered!
Calling ioctl() to re-read partition table.
Syncing disks.
root@vl:~# fdisk -l /dev/sdb
WARNING: GPT (GUID Partition Table) detected on '/dev/sdb'! The util fdisk doesn't support GPT. Use GNU Parted.
Disk /dev/sdb: 100.0 GB, 100030242816 bytes
255 heads, 63 sectors/track, 12161 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000
Device Boot Start End Blocks Id System
root@vl:~
「ファームウェア更新」をクリック
「はい」をクリック
やっぱり
一緒。
root@vl:~# parted -s /dev/sdb print Warning: /dev/sdb contains GPT signatures, indicating that it has a GPT table. However, it does not have a valid fake msdos partition table, as it should. Perhaps it was corrupted -- possibly by a program that doesn't understand GPT partition tables. Or perhaps you deleted the GPT table, and are now using an msdos partition table. Is this a GPT partition table? Model: ViPowER VP-89118(SD1) (scsi) Disk /dev/sdb: 100GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags root@vl:~# parted -s /dev/sdb mkpart primary 0 1024M Warning: The resulting partition is not properly aligned for best performance. root@vl:~# parted -s /dev/sdb mkpart primary 1024M 6144M root@vl:~# parted -s /dev/sdb mkpart primary 6144M 6145M root@vl:~# parted -s /dev/sdb mkpart primary 6145M 6146M root@vl:~# parted -s /dev/sdb mkpart primary 6146M 7168M root@vl:~# parted -s /dev/sdb mkpart primary 7168M 100GB root@vl:~# parted -s /dev/sdb print Model: ViPowER VP-89118(SD1) (scsi) Disk /dev/sdb: 100GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 17.4kB 1024MB 1024MB primary 2 1024MB 6144MB 5119MB primary 3 6144MB 6145MB 1049kB primary 4 6145MB 6146MB 1049kB primary 5 6146MB 7168MB 1022MB primary 6 7168MB 100GB 92.9GB primary root@vl:~#ちょっと違うけど、まあええか。
「ファームウェア更新」をクリック
「はい」をクリック
やっぱり
あかんか、、、
|
|
← 廃品回収リベンジ（５）LS-WSGL カーネルで起動して LS-SL ファームウェア 1.24 のインストール |
ハックの記録 LinkStation／玄箱 をハックしよう |
→ 廃品回収リベンジ（７） LS-SL ファームウェア 1.11 で boot して LinkStation シリースファームウェア 1.60 をインストール |
Copyright (C) 2003-2012 Yasunari Yamashita. All Rights Reserved.
yasunari ＠ yamasita.jp 山下康成＠京都府向日市
