|
BUFFALO INC. LinkStation series LS-GL(IESADA) LS-GL530 login: root root@LS-GL530:~#
root@LS-GL530:~# fdisk fdisk /dev/sda The number of cylinders for this disk is set to 38913. There is nothing wrong with that, but this is larger than 1024, and could in certain setups cause problems with: 1) software that runs at boot time (e.g., old versions of LILO) 2) booting and partitioning software from other OSs (e.g., DOS FDISK, OS/2 FDISK) Command (m for help): p Disk /dev/sda: 320.0 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 1 25 200781 83 Linux /dev/sda2 26 87 498015 83 Linux /dev/sda4 88 38913 311869845 5 Extended /dev/sda5 88 104 136521 82 Linux swap /dev/sda6 105 38913 311733261 83 Linux Command (m for help): d Partition number (1-6): 4 Command (m for help): d Partition number (1-4): 2 Command (m for help): d Selected partition 1 Command (m for help): p Disk /dev/sda: 320.0 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System Command (m for help): w The partition table has been altered! Calling ioctl() to re-read partition table. WARNING: Re-reading the partition table failed with error 16: Device or resource busy. The kernel still uses the old table. The new table will be used at the next reboot. Syncing disks. root@LS-GL530:~#
yasunari@ude:~$ cd /srv/tftp/ yasunari@ude:/srv/tftp$ ls HS-DHGL_1.20 LS-CHL_1.21 LS-CL_1.11 LS-LGL_2.01 LS-QL_1.10b LS-XHL_1.02+telnet SheevaPlug_1.2 LS-CHL_1.10 LS-CL+HackKit LS-GL_1.15 LS-QL_1.05+telnet LS-WSGL_1.06 LS-XHL_1.04b initrd.buffalo LS-CHL_1.20 LS-CL_1.07 LS-HGL_1.07b LS-QL_1.07b LS-XHL_1.02 LS-XHL_1.10 uImage.buffalo yasunari@ude:/srv/tftp$ rm initrd.buffalo uImage.buffalo yasunari@ude:/srv/tftp$ ln LS-GL_1.15/* . yasunari@ude:/srv/tftp$
ファームウェアアップデータを実行して まっさらに。 電源断
ude:~/tool# sh telnetable_091206.sh + mkdir /tmp/root + mount /dev/sdb2 /tmp/root + cd /tmp/root/etc + mv shadow shadow.orig + sed -e 's/^\(root:\)[^:]*\(:.*\)$/\1\2/' shadow.orig + chmod 600 shadow + '[' -f /tmp/root/usr/sbin/telnetd ']' + echo + echo /usr/sbin/telnetd + cd / + umount /tmp/root ude:~/tool#なんか、あっさり終わりすぎて本当にやったの？って思ってしまう。
ude:~/tool# mv telnetable_091206.sh telnetable_091214.sh
ude:~/tool# vi telnetable_091214.sh
:
ude:~/tool# cat !$
cat telnetable_091214.sh
#!/bin/sh
set -x
mkdir /tmp/root
mount /dev/sdb2 /tmp/root || exit
# shadow
cd /tmp/root/etc
mv shadow shadow.orig
sed -e 's/^\(root:\)[^:]*\(:.*\)$/\1\2/' shadow.orig > shadow
chmod 600 shadow
grep root shadow
# telnetd
if [ -f /tmp/root/usr/sbin/telnetd ]
then
echo >> /tmp/root/etc/init.d/rcS
echo /usr/sbin/telnetd >> /tmp/root/etc/init.d/rcS
tail /tmp/root/etc/init.d/rcS
fi
cd /
umount /tmp/root
ude:~/tool#
これで、少しは動きが見えるかな。次回確認、、、っていつ？
BUFFALO INC. LinkStation series LS-GL(IESADA) LS-GL530 login: root root@LS-GL530:~#
root@LS-GL530:~# date Fri Jun 26 06:08:43 JST 2009 root@LS-GL530:~# date 121421342009 Mon Dec 14 21:34:00 JST 2009 root@LS-GL530:~#長いこと起動していないので、内蔵クロックのバッテリも切れたか
Dec 14 21:36:29 LS-GL530 kernel: usb 2-1: new high speed USB device using ehci_platform and address 2 /sbin/hotplug [usb] /sbin/hotplug [usb] /sbin/hotplug [scsi_host] /sbin/hotplug [usb_device] Dec 14 21:36:29 LS-GL530 kernel: usb 2-1: configuration #1 chosen from 1 choice Dec 14 21:36:29 LS-GL530 kernel: scsi2 : SCSI emulation for USB Mass Storage devices Vendor: ViPowER Model: VP-89118(SD1) Rev: 2.10 Type: Direct-Access ANSI SCSI revision: 04 /sbin/hotplug [scsi] SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB) sdb: Write Protect is off sdb: assuming drive cache: write through /sbin/hotplug [block] SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB) sdb: Write Protect is off sdb: assuming drive cache: write through /sbin/hotplug [block] sd 2:0:0:0: Attached scsi disk sdb /sbin/hotplug [block] /sbin/hotplug [block] /sbin/hotplug [scsi_device] /sbin/hotplug [block] sd 2:0:0:0: Attached scsi generic sg1 type 0 /sbin/hotplug [scsi_generic] Dec 14 21:36:34 LS-GL530 kernel: Vendor: ViPowER Model: VP-89118(SD1) Rev: 2.10 Dec 14 21:36:34 LS-GL530 kernel: Type: Direct-Access ANSI SCSI revision: 04 Dec 14 21:36:34 LS-GL530 kernel: SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB) Dec 14 21:36:34 LS-GL530 kernel: sdb: Write Protect is off Dec 14 21:36:34 LS-GL530 kernel: sdb: assuming drive cache: write through Dec 14 21:36:34 LS-GL530 kernel: SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB) Dec 14 21:36:34 LS-GL530 kernel: sdb: Write Protect is off Dec 14 21:36:34 LS-GL530 kernel: sdb: assuming drive cache: write through Dec 14 21:36:35 LS-GL530 kernel: sdb: sdb1 sdb2 sdb3 sdb4 Dec 14 21:36:35 LS-GL530 kernel: sd 2:0:0:0: Attached scsi disk sdb Dec 14 21:36:35 LS-GL530 kernel: sd 2:0:0:0: Attached scsi generic sg1 type 0 /sbin/hotplug [block] Dec 14 21:36:36 LS-GL530 kernel: kjournald starting. Commit interval 5 seconds Dec 14 21:36:36 LS-GL530 kernel: EXT3 FS on sdb1, internal journal Dec 14 21:36:36 LS-GL530 kernel: EXT3-fs: mounted filesystem with ordered data mode. Dec 14 21:36:36 LS-GL530 nmbd[869]: [2009/12/14 21:36:36, 0] nmbd/nmbd.c:terminate(58) Dec 14 21:36:36 LS-GL530 nmbd[869]: Got SIGTERM: going down... Dec 14 21:36:37 LS-GL530 atalkd[852]: done Dec 14 21:36:37 LS-GL530 afpd[938]: shutting down on signal 15
root@LS-GL530:~# df Filesystem 1k-blocks Used Available Use% Mounted on /dev/sda2 493212 212488 280724 43% / /dev/ram1 15360 84 15276 1% /mnt/ram /dev/ls_disk1_1 194443 10925 173479 6% /boot /dev/ls_disk1_6 311602188 68160 311534028 0% /mnt/disk1 /dev/ls_usbdisk1_1 241116 10729 217939 5% /mnt/usbdisk1 root@LS-GL530:~# umount /mnt/usbdisk1/ /sbin/hotplug [block] root@LS-GL530:~#
root@LS-GL530:~# sh mk_partition_091207.sh The number of cylinders for this disk is set to 30401. There is nothing wrong with that, but this is larger than 1024, and could in certain setups cause problems with: 1) software that runs at boot time (e.g., old versions of LILO) 2) booting and partitioning software from other OSs (e.g., DOS FDISK, OS/2 FDISK) Command (m for help): Disk /dev/sdb: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdb1 1 31 248976 83 Linux /dev/sdb2 32 281 2008125 83 Linux /dev/sdb3 282 313 257040 82 Linux swap /dev/sdb4 314 30401 241681860 83 Linux Command (m for help): Partition number (1-4): Command (m for help): Partition number (1-4): Command (m for help): Partition number (1-4): Command (m for help): Selected partition 1 Command (m for help): Disk /dev/sdb: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System Command (m for help): Command action e extended p primary partition (1-4) Partition number (1-4): First cylinder (1-30401, default 1): Using default value 1 Last cylinder or +size or +sizeM or +sizeK (1-30401, default 30401): Command (m for help): Command action e extended p primary partition (1-4) Partition number (1-4): First cylinder (32-30401, default 32): Using default value 32 Last cylinder or +size or +sizeM or +sizeK (32-30401, default 30401): Command (m for help): Command action e extended p primary partition (1-4) Partition number (1-4): First cylinder (282-30401, default 282): Using default value 282 Last cylinder or +size or +sizeM or +sizeK (282-30401, default 30401): Command (m for help): Command action e extended p primary partition (1-4) Selected partition 4 First cylinder (314-30401, default 314): Using default value 314 Last cylinder or +size or +sizeM or +sizeK (314-30401, default 30401): Using default value 30401 Command (m for help): Disk /dev/sdb: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdb1 1 31 248976 83 Linux /dev/sdb2 32 281 2008125 83 Linux /dev/sdb3 282 313 257040 83 Linux /dev/sdb4 314 30401 241681860 83 Linux Command (m for help): Partition number (1-4): Hex code (type L to list codes): Changed system type of partition 3 to 82 (Linux swap) Command (m for help): Disk /dev/sdb: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdb1 1 31 248976 83 Linux /dev/sdb2 32 281 2008125 83 Linux /dev/sdb3 282 313 257040 82 Linux swap /dev/sdb4 314 30401 241681860 83 Linux Command (m for help): The partition table has been altered! Calling ioctl() to re-read partition table. /sbin/hotplug [block] /sbin/hotplug [block] /sbin/hotplug [block] /sbin/hotplug [block] SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB) sdb: Write Protect is off sdb: assuming drive cache: write through /sbin/hotplug [block] /sbin/hotplug [block] /sbin/hotplug [block] /sbin/hotplug [block] /sbin/hotplug [block] /sbin/hotplug [block] /sbin/hotplug [block] /sbin/hotplug [block] SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB) sdb: Write Protect is off sdb: assuming drive cache: write through /sbin/hotplug [block] /sbin/hotplug [block] /sbin/hotplug [block] /sbin/hotplug [block] Syncing disks. root@LS-GL530:~#念のため、確認
root@LS-GL530:~# fdisk -l /dev/sdb Disk /dev/sdb: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdb1 1 31 248976 83 Linux /dev/sdb2 32 281 2008125 83 Linux /dev/sdb3 282 313 257040 82 Linux swap /dev/sdb4 314 30401 241681860 83 Linux root@LS-GL530:~#これも、スクリプトの最後でやっておいた方がいいな
root@LS-GL530:~# cd /mnt/disk1/share/hackkit/hackkit_config root@LS-GL530:/mnt/disk1/share/hackkit# echo HOSTNAME=nino >> hackkit_config root@LS-GL530:/mnt/disk1/share/hackkit# cat !$ cat hackkit_config ADDRESS=192.168.2.42 HOSTNAME=nino root@LS-GL530:/mnt/disk1/share/hackkit#
root@LS-GL530:/mnt/disk1/share/hackkit# sh hackkit_091128.sh
PRODUCTID = 0x00000009
MACHINE LSGL
formating hard drive ...
mke2fs 1.27 (8-Mar-2002)
Filesystem label=
OS type: Linux
Block size=1024 (log=0)
Fragment size=1024 (log=0)
62248 inodes, 248976 blocks
12448 blocks (5.00%) reserved for the super user
First data block=1
31 block groups
8192 blocks per group, 8192 fragments per group
2008 inodes per group
Superblock backups stored on blocks:
8193, 24577, 40961, 57345, 73729, 204801, 221185
Writing inode tables: done
Creating journal (4096 blocks): done
Writing superblocks and filesystem accounting information: done
This filesystem will be automatically checked every 30 mounts or
180 days, whichever comes first. Use tune2fs -c or -i to override.
meta-data=/dev/sdb2 isize=256 agcount=8, agsize=62754 blks
= sectsz=512
data = bsize=4096 blocks=502031, imaxpct=25
= sunit=0 swidth=0 blks, unwritten=1
naming =version 2 bsize=4096
log =internal log bsize=4096 blocks=2560, version=1
= sectsz=512 sunit=0 blks
realtime =none extsz=65536 blocks=0, rtextents=0
Setting up swapspace version 1, size = 263204864 bytes
meta-data=/dev/sdb4 isize=256 agcount=58, agsize=1048576 blks
= sectsz=512
data = bsize=4096 blocks=60420465, imaxpct=25
= sunit=0 swidth=0 blks, unwritten=1
naming =version 2 bsize=4096
log =internal log bsize=4096 blocks=29502, version=1
= sectsz=512 sunit=0 blks
realtime =none extsz=65536 blocks=0, rtextents=0
mounting root file system ...
XFS mounting filesystem sdb2
extracting hackkit archive ...
/sbin/hotplug [block]
./
./var/
./var/lib/
./var/lib/apt/
./var/lib/apt/lists/
:
:
./media/
./initrd/
copying miconapl ...
usr/local/sbin/miconapl
usr/local/lib/libbuffalo_bin.so
creating miconapl ...
creating fancontrol ...
creating kernelmon ...
copying /lib/modules ...
lib/modules/
lib/modules/2.6.16.16-arm1/
lib/modules/2.6.16.16-arm1/kernel/
:
:
lib/modules/2.6.16.16-arm1/modules.alias
lib/modules/2.6.16.16-arm1/modules.symbols
creating usb ...
/sbin/hotplug [block]
checking /dev/sdb1
fsck 1.27 (8-Mar-2002)
e2fsck 1.27 (8-Mar-2002)
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sdb1: 11/62248 files (0.0% non-contiguous), 11987/248976 blocks
mounting /boot ...
/sbin/hotplug [block]
copying /boot ...
initrd.buffalo
uImage.buffalo
editing initrd ...
75826+1 records in
75826+1 records out
gunziping /mnt/debinst/boot/initrd.gz ...
EXT2-fs warning: checktime reached, running e2fsck is recommended
/sbin/hotplug [block]
/sbin/hotplug [block]
gziping /mnt/debinst/boot/initrd ... wait 5 minutes
Image Name: initrd
Created: Mon Dec 14 21:45:04 2009
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4835957 Bytes = 4722.61 kB = 4.61 MB
Load Address: 0x00000000
Entry Point: 0x00000000
unmount /boot ...
umount: /mnt/debinst/boot: device is busy
umount: /mnt/debinst/boot: device is busy
root@LS-GL530:/mnt/disk1/share/hackkit#
: : ---- in hackkit linuxrc --- XFS mounting filesystem sda2 VFS: Mounted root (xfs filesystem). Trying to move old root to /initrd ... okay Freeing init memory: 108K INIT: version 2.86 booting Setting the system clock. Activating swap...Adding 257032k swap on /dev/sda3. Priority:-1 extents:1 across:257032k done. Setting the system clock. Cleaning up ifupdown.... Loading kernel modules...done. Checking file systems...fsck 1.41.3 (12-Oct-2008) /dev/sda1: recovering journal /dev/sda1: Clearing orphaned inode 6025 (uid=0, gid=0, mode=0100644, size=14680064) /dev/sda1: Superblock last mount time is in the future. FIXED. /dev/sda1: Backing up journal inode block information. /dev/sda1 has filesystem last checked time in the future, check forced. /dev/sda1: 13/62248 files (15.4% non-contiguous), 18506/248976 blocks /sbin/fsck.xfs: XFS file system. fsck died with exit status 1 done. Setting kernel variables (/etc/sysctl.conf)...Unknown HZ value! (113) Assume 100. done. Mounting local filesystems...kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. XFS mounting filesystem sda4 done. Activating swapfile swap...done. Setting up networking.... Configuring network interfaces...eth0: link down done. err: >AnalyzeRecvPacket:This is invalid RespCode.(code=244) eth0: link up<5>, full duplex<5>, speed 1 Gbps<5> INIT: Entering runlevel: 2 Starting enhanced syslogd: rsyslogd. Starting internet superserver: inetd. Starting periodic command scheduler: crond. Debian GNU/Linux 5.0 nino ttyS0 nino login:
Debian GNU/Linux 5.0 nino ttyS0 nino login: guest Password: Linux nino 2.6.16.16-arm1 #37 Tue May 20 10:01:57 JST 2008 armv5tejl The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. No directory, logging in with HOME=/ guest@nino:/$
guest@nino:/$ su - root Password: nino:~#
nino:~# tail -f /var/log/messages : : usb 2-1: new high speed USB device using ehci_platform and address 2 usb 2-1: configuration #1 chosen from 1 choice scsi2 : SCSI emulation for USB Mass Storage devices Jun 26 06:26:27 nino kernel: usb 2-1: new high speed USB device using ehci_platform and address 2 Jun 26 06:26:27 nino kernel: usb 2-1: configuration #1 chosen from 1 choice Jun 26 06:26:27 nino kernel: scsi2 : SCSI emulation for USB Mass Storage devices Vendor: BUFFALO Model: ClipDrive Rev: 2.00 Type: Direct-Access ANSI SCSI revision: 02 Jun 26 06:26:32 nino kernel: Vendor: BUFFALO Model: ClipDrive Rev: 2.00 Jun 26 06:26:32 nino kernel: Type: Direct-Access ANSI SCSI revision: 02 ready SCSI device sdb: 256000 512-byte hdwr sectors (131 MB) sdb: Write Protect is off sdb: assuming drive cache: write through SCSI device sdb: 256000 512-byte hdwr sectors (131 MB) sdb: Write Protect is off sdb: assuming drive cache: write through sdb: sdb1 sd 2:0:0:0: Attached scsi removable disk sdb sd 2:0:0:0: Attached scsi generic sg1 type 0 Jun 26 06:26:33 nino kernel: ready Jun 26 06:26:33 nino kernel: SCSI device sdb: 256000 512-byte hdwr sectors (131 MB) Jun 26 06:26:33 nino kernel: sdb: Write Protect is off Jun 26 06:26:33 nino kernel: SCSI device sdb: 256000 512-byte hdwr sectors (131 MB) Jun 26 06:26:33 nino kernel: sdb: Write Protect is off Jun 26 06:26:33 nino kernel: sdb: sdb1 Jun 26 06:26:33 nino kernel: sd 2:0:0:0: Attached scsi removable disk sdb Jun 26 06:26:33 nino kernel: sd 2:0:0:0: Attached scsi generic sg1 type 0 usb 2-1: USB disconnect, address 2 Jun 26 06:27:28 nino kernel: usb 2-1: USB disconnect, address 2OK
usb 2-1: new high speed USB device using ehci_platform and address 3 usb 2-1: configuration #1 chosen from 1 choice Jun 26 06:27:39 nino kernel: usb 2-1: new high speed USB device using ehci_platform and address 3 Jun 26 06:27:39 nino kernel: usb 2-1: configuration #1 chosen from 1 choice usb 2-1: USB disconnect, address 3 Jun 26 06:27:58 nino kernel: usb 2-1: USB disconnect, address 3LS-GL はプリンタがサポートされていないので、認識しなくても OK
時計が狂ってるな、、、
nino:~# date 121421532009 Mon Dec 14 21:53:00 JST 2009 nino:~# date Mon Dec 14 21:53:03 JST 2009 nino:~#リブートして時間を見る
nino:~# shutdown -r now Broadcast message from root@nino (ttyS0) (Mon Dec 14 21:53:57 2009): The system is going down for reboot NOW! INIT: Sending pStopping internet superserver: inetd. Saving the system clock. Stopping enhanced syslogd: rsyslogd. Asking all remaining processes to terminate...done. Killing all remaining processes...failed. Deconfiguring network interfaces...done. Cleaning up ifupdown.... Deactivating swap...done. Unmounting local filesystems...done. Will now restart. Synchronizing SCSI cache for disk sda: Restarting system. . >miconCntl_Reboot : : Debian GNU/Linux 5.0 nino ttyS0 nino login: root Password: Linux nino 2.6.16.16-arm1 #37 Tue May 20 10:01:57 JST 2008 armv5tejl The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. nino:~# date Mon Dec 14 21:55:01 JST 2009 nino:~#とりあえず、リブートでは問題なし。
Debian GNU/Linux 5.0 nino ttyS0 nino login: guest Password: Last login: Fri Jun 26 06:25:31 JST 2009 on ttyS0 Linux nino 2.6.16.16-arm1 #37 Tue May 20 10:01:57 JST 2008 armv5tejl The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. No directory, logging in with HOME=/ guest@nino:/$
guest@nino:/$ su - root Password: nino:~#
nino:~# date Mon Dec 14 21:57:29 JST 2009 nino:~#
nino:~# sh -x setup_090717.sh + echo passwd root passwd root + passwd root Enter new UNIX password: Retype new UNIX password: passwd: password updated successfully + addgroup --gid 1001 yamasita Adding group `yamasita' (GID 1001) ... Done. + echo adduser yasunari adduser yasunari + adduser --home /home/yamasita/yasunari --ingroup yamasita --uid 1001 --gecos 'Yasunari Yamashita' yasunari Adding user `yasunari' ... Adding new user `yasunari' (1001) with group `yamasita' ... Creating home directory `/home/yamasita/yasunari' ... Copying files from `/etc/skel' ... Enter new UNIX password: Retype new UNIX password: passwd: password updated successfully + deluser guest Removing user `guest' ... Warning: group `guest' has no more members. userdel: user guest is currently logged in /usr/sbin/deluser: `/usr/sbin/userdel guest' returned error code 8. Exiting. + apt-get update Hit http://ftp.jp.debian.org lenny Release.gpg Hit http://ftp.jp.debian.org lenny Release Ign http://ftp.jp.debian.org lenny/main Packages/DiffIndex Ign http://ftp.jp.debian.org lenny/main Sources/DiffIndex Hit http://ftp.jp.debian.org lenny/main Packages Hit http://ftp.jp.debian.org lenny/main Sources Get:1 http://security.debian.org lenny/updates Release.gpg [835B] Get:2 http://security.debian.org lenny/updates Release [40.8kB] Ign http://security.debian.org lenny/updates/main Packages/DiffIndex Ign http://security.debian.org lenny/updates/main Sources/DiffIndex Get:3 http://security.debian.org lenny/updates/main Packages [297kB] Get:4 http://security.debian.org lenny/updates/main Sources [78.5kB] Fetched 417kB in 8s (47.2kB/s) Reading package lists... Done + apt-get upgrade Reading package lists... Done Building dependency tree Reading state information... Done 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. + apt-get install ntp Reading package lists... Done Building dependency tree Reading state information... Done The following extra packages will be installed: libcap1 libedit2 perl perl-modules Suggested packages: ntp-doc perl-doc libterm-readline-gnu-perl libterm-readline-perl-perl The following NEW packages will be installed: libcap1 libedit2 ntp perl perl-modules 0 upgraded, 5 newly installed, 0 to remove and 0 not upgraded. Need to get 8262kB of archives. After this operation, 29.7MB of additional disk space will be used. Do you want to continue [Y/n]? y Get:1 http://ftp.jp.debian.org lenny/main libedit2 2.11~20080614-1 [64.5kB] Get:2 http://ftp.jp.debian.org lenny/main perl-modules 5.10.0-19lenny2 [3198kB] Get:3 http://security.debian.org lenny/updates/main ntp 1:4.2.4p4+dfsg-8lenny3 [459kB] Get:4 http://ftp.jp.debian.org lenny/main perl 5.10.0-19lenny2 [4532kB] Get:5 http://ftp.jp.debian.org lenny/main libcap1 1:1.10-14 [9074B] Fetched 8262kB in 6s (1302kB/s) Selecting previously deselected package libedit2. (Reading database ... 8602 files and directories currently installed.) Unpacking libedit2 (from .../libedit2_2.11~20080614-1_armel.deb) ... Selecting previously deselected package perl-modules. Unpacking perl-modules (from .../perl-modules_5.10.0-19lenny2_all.deb) ... Selecting previously deselected package perl. Unpacking perl (from .../perl_5.10.0-19lenny2_armel.deb) ... Selecting previously deselected package libcap1. Unpacking libcap1 (from .../libcap1_1%3a1.10-14_armel.deb) ... Selecting previously deselected package ntp. Unpacking ntp (from .../ntp_1%3a4.2.4p4+dfsg-8lenny3_armel.deb) ... Processing triggers for man-db ... Setting up libedit2 (2.11~20080614-1) ... Setting up libcap1 (1:1.10-14) ... Setting up ntp (1:4.2.4p4+dfsg-8lenny3) ... Starting NTP server: ntpd. Setting up perl-modules (5.10.0-19lenny2) ... Setting up perl (5.10.0-19lenny2) ... + mv /etc/ntp.conf /etc/ntp.conf.orig + sed -e 's/^server/# server/' -e '/ntp.your-provider.example/aserver ntp3.jst.mfeed.ad.jp\ server ntp2.jst.mfeed.ad.jp\ server ntp1.jst.mfeed.ad.jp' /etc/ntp.conf.orig + apt-get install samba Reading package lists... Done Building dependency tree Reading state information... Done The following extra packages will be installed: libcups2 libkeyutils1 libkrb53 libldap-2.4-2 libtalloc1 libwbclient0 samba-common ucf Suggested packages: cups-common krb5-doc krb5-user smbldap-tools ldb-tools The following NEW packages will be installed: libcups2 libkeyutils1 libkrb53 libldap-2.4-2 libtalloc1 libwbclient0 samba samba-common ucf 0 upgraded, 9 newly installed, 0 to remove and 0 not upgraded. Need to get 8614kB of archives. After this operation, 23.0MB of additional disk space will be used. Do you want to continue [Y/n]? y Get:1 http://ftp.jp.debian.org lenny/main libkeyutils1 1.2-9 [5228B] Get:2 http://ftp.jp.debian.org lenny/main libkrb53 1.6.dfsg.4~beta1-5lenny1 [449kB] Get:3 http://ftp.jp.debian.org lenny/main libldap-2.4-2 2.4.11-1 [179kB] Get:4 http://ftp.jp.debian.org lenny/main ucf 3.0016 [64.4kB] Get:5 http://ftp.jp.debian.org lenny/main libtalloc1 1.2.0~git20080616-1 [13.3kB] Get:6 http://security.debian.org lenny/updates/main libcups2 1.3.8-1+lenny7 [158kB] Get:7 http://security.debian.org lenny/updates/main libwbclient0 2:3.2.5-4lenny7 [78.8kB] Get:8 http://security.debian.org lenny/updates/main samba-common 2:3.2.5-4lenny7 [3372kB] Get:9 http://security.debian.org lenny/updates/main samba 2:3.2.5-4lenny7 [4294kB] Fetched 8614kB in 43s (196kB/s) Preconfiguring packages ... Package configuration lqqqqqqqqqqqqqqqqqqqqqqqqqqqqu Samba Server tqqqqqqqqqqqqqqqqqqqqqqqqqqqqk x Please specify the workgroup you want this server to appear to be in x x when queried by clients. Note that this parameter also controls the x x domain name used with the security=domain setting. x x x x Workgroup/Domain Name: x x x x YAMASITA______________________________________________________________ x x x x問題なさそう。x x x mqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj Package configuration lqqqqqqqqqqqqqqqqqqqqqqqqqqqqqu Samba Server tqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqk x x x If your computer gets IP address information from a DHCP server on the x x network, the DHCP server may also provide information about WINS servers x x ("NetBIOS name servers") present on the network. This requires a change x x to your smb.conf file so that DHCP-provided WINS settings will x x automatically be read from /etc/samba/dhcp.conf. x x x x The dhcp3-client package must be installed to take advantage of this x x feature. x x x x Modify smb.conf to use WINS settings from DHCP? x x x x x x x mqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj Selecting previously deselected package libkeyutils1. (Reading database ... 9854 files and directories currently installed.) Unpacking libkeyutils1 (from .../libkeyutils1_1.2-9_armel.deb) ... Selecting previously deselected package libkrb53. Unpacking libkrb53 (from .../libkrb53_1.6.dfsg.4~beta1-5lenny1_armel.deb) ... Selecting previously deselected package libldap-2.4-2. Unpacking libldap-2.4-2 (from .../libldap-2.4-2_2.4.11-1_armel.deb) ... Selecting previously deselected package ucf. Unpacking ucf (from .../archives/ucf_3.0016_all.deb) ... Moving old data out of the way Selecting previously deselected package libcups2. Unpacking libcups2 (from .../libcups2_1.3.8-1+lenny7_armel.deb) ... Selecting previously deselected package libtalloc1. Unpacking libtalloc1 (from .../libtalloc1_1.2.0~git20080616-1_armel.deb) ... Selecting previously deselected package libwbclient0. Unpacking libwbclient0 (from .../libwbclient0_2%3a3.2.5-4lenny7_armel.deb) ... Selecting previously deselected package samba-common. Unpacking samba-common (from .../samba-common_2%3a3.2.5-4lenny7_armel.deb) ... Selecting previously deselected package samba. Unpacking samba (from .../samba_2%3a3.2.5-4lenny7_armel.deb) ... Processing triggers for man-db ... Setting up libkeyutils1 (1.2-9) ... Setting up libkrb53 (1.6.dfsg.4~beta1-5lenny1) ... Setting up libldap-2.4-2 (2.4.11-1) ... Setting up ucf (3.0016) ... Setting up libcups2 (1.3.8-1+lenny7) ... Setting up libtalloc1 (1.2.0~git20080616-1) ... Setting up libwbclient0 (2:3.2.5-4lenny7) ... Setting up samba-common (2:3.2.5-4lenny7) ... Creating config file /etc/samba/smb.conf with new version Setting up samba (2:3.2.5-4lenny7) ... Generating /etc/default/samba... tdbsam_open: Converting version 0 database to version 3. account_policy_get: tdb_fetch_uint32 failed for field 1 (min password length), returning 0 account_policy_get: tdb_fetch_uint32 failed for field 2 (password history), returning 0 account_policy_get: tdb_fetch_uint32 failed for field 3 (user must logon to change password), returning 0 account_policy_get: tdb_fetch_uint32 failed for field 4 (maximum password age), returning 0 account_policy_get: tdb_fetch_uint32 failed for field 5 (minimum password age), returning 0 account_policy_get: tdb_fetch_uint32 failed for field 6 (lockout duration), returning 0 account_policy_get: tdb_fetch_uint32 failed for field 7 (reset count minutes), returning 0 account_policy_get: tdb_fetch_uint32 failed for field 8 (bad lockout attempt), returning 0 account_policy_get: tdb_fetch_uint32 failed for field 9 (disconnect time), returning 0 account_policy_get: tdb_fetch_uint32 failed for field 10 (refuse machine password change), returning 0 Importing account for root...ok Importing account for daemon...ok Importing account for bin...ok Importing account for sys...ok Importing account for sync...ok Importing account for games...ok Importing account for man...ok Importing account for lp...ok Importing account for mail...ok Importing account for news...ok Importing account for uucp...ok Importing account for proxy...ok Importing account for www-data...ok Importing account for backup...ok Importing account for list...ok Importing account for irc...ok Importing account for gnats...ok Importing account for nobody...ok Importing account for libuuid...ok Importing account for guest...ok Importing account for telnetd...ok Importing account for yasunari...ok Importing account for ntp...ok Adding group `sambashare' (GID 105) ... Done. Starting Samba daemons: nmbd smbd. + echo + echo '[share]' + echo ' comment = hackkit share' + echo ' path = /mnt' + echo ' writable = Yes' + echo ' create mask = 0660' + echo ' directory mask = 0770' + /etc/init.d/samba reload Reloading /etc/samba/smb.conf: smbd only. + echo smbpasswd -a yasunari smbpasswd -a yasunari + smbpasswd -a yasunari New SMB password: Retype new SMB password: + mkdir /mnt/share + chgrp yamasita /mnt/share/ + chmod g+w /mnt/share + apt-get install inetutils-ftpd Reading package lists... Done Building dependency tree Reading state information... Done The following NEW packages will be installed: inetutils-ftpd 0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded. Need to get 94.1kB of archives. After this operation, 197kB of additional disk space will be used. Get:1 http://ftp.jp.debian.org lenny/main inetutils-ftpd 2:1.5.dfsg.1-9 [94.1kB] Fetched 94.1kB in 0s (212kB/s) Selecting previously deselected package inetutils-ftpd. (Reading database ... 10031 files and directories currently installed.) Unpacking inetutils-ftpd (from .../inetutils-ftpd_2%3a1.5.dfsg.1-9_armel.deb) ... Processing triggers for man-db ... Setting up inetutils-ftpd (2:1.5.dfsg.1-9) ... + echo 'ftp stream tcp nowait root /usr/sbin/tcpd ftpd' ++ cat /var/run/inetd.pid + kill -HUP 536 + apt-get clean nino:~#
さて、全機種確認が終わったので、マスターを焼く
|
|
← 作り直したハックキットの確認（７）LS-CL |
ハックの記録 LinkStation／玄箱 をハックしよう |
→ LS-WXL/LS-WSXL シリーズファームウェア アップデータ Ver.1.22 |
