複製した HDD から起動

Orion1   CPU =  Low

Checking DATA BUS
Checking ADDRESS BUS

> Checking hardware info ...
=== CPU-ID       : 0x00005182 ===
=== Strap status : 0x00802030 ===
=== H/W boardId  :       0x33 ===
=== boardId      :       0x1a ===
=== micon_support:        off ===
> OK.
=== BUFFALO LS-SL U-Boot. ===
 ** LOADER **
 ** BUFFALO BOARD: BUFFALO_BOARD_LS_SL LE (CFG_ENV_ADDR=fffff000)


U-Boot 1.1.1 (May 28 2009 - 11:06:21) Marvell version: 1.12.1 - TINY
U-Boot code: 00600000 -> 00639A58  BSS: -> 00641B24
Buffalo Version: 1.23-1.00

DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done

Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
Orion 1 streaming disabled
SysClock = 200Mhz , TClock = 166Mhz


USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net:   egiga0 [PRIME]
Using 88E1118 phy
buffalo_change_power_status > Read 0x5c
buffalo_IsStopAtUbootStatus > MagicKey=0x5c
buffalo_change_power_status > Read 0x5c
buffalo_change_power_status > Read 0x5c
buffalo_change_power_status > Writing 0x5c

Please Press HDD power button to continue ...
buffalo_change_power_status > Read 0x5c
buffalo_change_power_status > Writing 0x3a

Marvell Serial ATA Adapter
Integrated Sata device found
  Device 1: OK
Model: Maxtor 6L200M0                           Firm: BANC1G10 Ser#: L40PVARG   
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 194481.0 MB = 189.9 GB (398297088 x 512)

** Bad partition 1 **
serch_boot_drv (194)>No kernel_file 0
** Bad partition 1 **
serch_boot_drv (249)>No init_file 0

2120012 bytes read
   Image Name:   Linux-2.6.22.7
   Created:      2009-06-14  13:44:50 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2119948 Bytes =  2 MB
   Load Address: 00008000
   Entry Point:  00008000

8937716 bytes read
   Image Name:   initrd
   Created:      2009-06-14  13:46:10 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    8937652 Bytes =  8.5 MB
   Load Address: 00000000
   Entry Point:  00000000
Booting from Device 1
hit any key to switch tftp boot.
Hit any key to stop autoboot:  0
Hit any key to stop autoboot:  0

2120012 bytes read

8937716 bytes read
## Booting image at 00100000 ...
   Image Name:   Linux-2.6.22.7
   Created:      2009-06-14  13:44:50 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2119948 Bytes =  2 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00800000 ...
   Image Name:   initrd
   Created:      2009-06-14  13:46:10 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    8937652 Bytes =  8.5 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

arg:console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 func=0 BOOTVER=1.23
CONFIG_BUFFALO_PLATFORM ---
Uncompressing Linux..................................................................................................................................... done, booting the kernel.
	:
	:
*** /usr/local/bin/DirectCopy_wait.sh [start]

BUFFALO INC. LinkStation series
LS-SL807 login: 1 USB_DEVICE=none
2 USB_DEVICE=none
3 USB_DEVICE=none
4 USB_DEVICE=none
5 USB_DEVICE=none
KERNELMOn (PSW_on)
Shutting down pwrmgr:


BUFFALO INC. LinkStation series
LS-SL807 login: root
No mail.
root@LS-SL807:~# cat /proc/mdstat
Personalities : [raid0] [raid1] [raid6] [raid5] [raid4]
md1 : active raid1 sda2[1]
      4999936 blocks [2/1] [_U]

md10 : active raid1 sda5[1]
      999872 blocks [2/1] [_U]

md0 : active raid1 sda1[1]
      999872 blocks [2/1] [_U]

unused devices: 
root@LS-SL807:~#

でも、、、、
LS-QL の時にも思ったが、
HDD が死んでも何のエラーも出ずに起動してくるというのは 良くないと思うんですが、、、

LS-SL 楽天市場