U-Boot

Orion1   CPU =  Low

Checking DATA BUS
Checking ADDRESS BUS

> Checking hardware info ...
=== CPU-ID       : 0x00005182 ===
=== Strap status : 0x00802030 ===
=== H/W boardId  :       0x33 ===
=== boardId      :       0x1a ===
=== micon_support:        off ===
> OK.
=== BUFFALO LS-SL U-Boot. ===
 ** LOADER **
 ** BUFFALO BOARD: BUFFALO_BOARD_LS_SL LE (CFG_ENV_ADDR=fffff000)


U-Boot 1.1.1 (May 28 2009 - 11:06:21) Marvell version: 1.12.1 - TINY
U-Boot code: 00600000 -> 00639A58  BSS: -> 00641B24
Buffalo Version: 1.23-1.00

DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done

Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
Orion 1 streaming disabled
SysClock = 200Mhz , TClock = 166Mhz


USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net:   egiga0 [PRIME]
Using 88E1118 phy
buffalo_change_power_status > Read 0x7a
buffalo_IsStopAtUbootStatus > MagicKey=0x7a
buffalo_change_power_status > Read 0x7a
buffalo_change_power_status > Read 0x7a
buffalo_change_power_status > Writing 0x5c

Please Press HDD power button to continue ...
buffalo_change_power_status > Read 0x5c
buffalo_change_power_status > Writing 0x3a

Marvell Serial ATA Adapter
Integrated Sata device found
  Device 0: OK
Model: WDC WD5000BEVT-00ZAT0                    Firm: 01.01A01 Ser#:      WD-WX50A79U4140
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)


2120012 bytes read
   Image Name:   Linux-2.6.22.7
   Created:      2009-06-14  13:44:50 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2119948 Bytes =  2 MB
   Load Address: 00008000
   Entry Point:  00008000

8937716 bytes read
   Image Name:   initrd
   Created:      2009-06-14  13:46:10 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    8937652 Bytes =  8.5 MB
   Load Address: 00000000
   Entry Point:  00000000
** Bad partition 1 **
serch_boot_drv (194)>No kernel_file 1
** Bad partition 1 **
serch_boot_drv (249)>No init_file 1
Booting from Device 0
hit any key to switch tftp boot.
Hit any key to stop autoboot:  0
Hit any key to stop autoboot:  0
Marvell>> help
?       - alias for 'help'
base    - print or set address offset
boot    - boot default, i.e., run 'bootcmd'
bootd   - boot default, i.e., run 'bootcmd'
bootm   - boot application image from memory
bootp   - boot image via network using BootP/TFTP protocol
bubt    - Burn an image on the Boot Flash.
cmp     - memory compare
cp      - memory copy
cpumap - Display CPU memory mapping settings.
crc32   - checksum calculation
date    - get/set/reset date & time
diskboot- boot from IDE device
echo    - echo args to console
erase   - erase FLASH memory
ext2load- load binary file from a Ext2 filesystem
ext2ls- list files in a directory (default /)
flinfo  - print FLASH memory information
go      - start application at address 'addr'
help    - print online help
ide     - IDE sub-system
loop    - infinite loop on address range
md      - memory display
mm      - memory modify (auto-incrementing)
mtest   - simple RAM test
mw      - memory write (fill)
nm      - memory modify (constant address)
pci     - list and access PCI Configuraton Space
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
resetenv        - Return all environment variable to default.
saveenv - save environment variables to persistent storage
setenv  - set environment variables
tftpboot- boot image via network using TFTP protocol
version - print monitor version
Marvell>> printenv
bootargs=$(bootargs_base) $(bootargs_root)
baudrate=115200
loads_echo=0
ipaddr=192.168.11.150
serverip=192.168.11.1
rootpath=/nfs/arm
cpuName=926
CASset=min
MALLOC_len=1
bootargs_end=:::DB88FXX81:eth0:none
buffalo_ver=BOOTVER=1.23
buffalo_minor_ver=BOOT_MINOR_VER=1.00
build_time=11:06:18
initrd=initrd.buffalo
kernel=uImage.buffalo
bootargs_base=console=ttyS0,115200
bootargs_root=root=/dev/sda2 rw initrd=0x00800040,15M panic=5
def_tftp=tftp 0x00100000 $(kernel); tftp 0x00800000 $(initrd); setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver) tftpboot=yes; bootm 0x00100000 0x00800000
ethact=egiga0
ethaddr=00:1D:73:F9:48:07
stdin=serial
stdout=serial
stderr=serial
enaMonExt=no
enaFlashBuf=yes
enaCpuStream=no
ethprime=egiga0
bootdelay=3
disaMvPnp=no
overEthAddr=no
usb0Mode=host
usb1Mode=host
bootargs_func=func=0
filesize=8860F4
bootcmd= ext2load ide 0:1 0x00100000 /$(kernel); ext2load ide 1:1 0x00800000 /$(initrd); setenv bootargs $(bootargs_base) $(bootargs_root) $(bootargs_func) $(bootargs_debug) $(buffalo_ver); bootm 0x00100000 0x00800000

Environment size: 1065/4092 bytes
Marvell>>

LS-SL 楽天市場