なんだ、LinkStation のファームウェアアップデータと同じ。
「インストール」 をクリック / Click "Install" button.
# df Filesystem Size Used Available Use% Mounted on tmpfs 61.9M 52.0K 61.9M 0% /tmp /dev/sda1 472.5M 10.3M 437.8M 2% /boot /dev/sda2 4.7G 137.7M 4.3G 3% /rootfs /dev/sda1 472.5M 10.3M 437.8M 2% /rootfs/boot # ls /rootfs/ boot lost+found # ls /rootfs/boot/ lost+found #OK を押す / Click "OK"
再度「インストール」 をクリック / Click "Install" button again.
今度は、インストールが進む。/ Install procedure is runnning.
U-Boot 2009.06-BUFFALO-svn1376 (Jul 11 2009 - 04:11:01) KURO-NAS/T4
CPU: MPC8245/8241 Revision 1.4 at 262.144 MHz: 16 kB I-Cache 16 kB D-Cache
DRAM: 128 MB
FLASH: 4 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: RTL8169#0
Boot in 05 seconds ('s' to stop)...Loading sata 0:1:uImage.buffalo
5111200 bytes read
## Booting kernel from FIT Image at 00500000 ...
Using 'conf@2' configuration
Trying 'kernel@1' kernel subimage
Description: Linux kernel
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x005000e8
Data Size: 1844364 Bytes = 1.8 MB
Architecture: PowerPC
OS: Linux
Load Address: 0x00000000
Entry Point: 0x00000000
Hash algo: sha1
Hash value: 845984557f1bab7570be096380a2cecbf3b09c25
Verifying Hash Integrity ... sha1+ OK
## Flattened Device Tree from FIT Image at 00500000
Using 'conf@2' configuration
Trying 'fdt@1' FDT blob subimage
Description: Flattened Device Tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x009deb0c
Data Size: 3836 Bytes = 3.7 kB
Architecture: PowerPC
Hash algo: sha1
Hash value: fba7f0b57375e53d725366543ce4c3c6e134bd89
Verifying Hash Integrity ... sha1+ OK
Booting using the fdt blob at 0x9deb0c
Uncompressing Kernel Image ... OK
Loading Device Tree to 007fc000, end 007ffefb ... OK
Using Buffalo Linkstation machine description
Linux version 2.6.30.1-BUFFALO-svn1376 (builder@BUFFALO) (gcc version 4.3.2 (Sourcery G++ Lite 4.3-50) ) #1 Sat Jul 11 04:37:22 JST 2009
console [udbg0] enabled
Adding PCI host bridge /soc10x/pci@fec00000
PCI host bridge /soc10x/pci@fec00000 (primary) ranges:
IO 0x00000000fe000000..0x00000000febfffff -> 0x0000000000000000
MEM 0x0000000080000000..0x00000000efffffff -> 0x0000000080000000
BUFFALO Network Attached Storage Series
(C) 2002-2009 BUFFALO INC.
Zone PFN ranges:
DMA 0x00000000 -> 0x00008000
Normal 0x00008000 -> 0x00008000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00008000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: root=/dev/sda2 console=ttyS1,57600 BOOTVER=0.00
NR_IRQS:512
mpic: Setting up MPIC " EPIC " version 1.2 at 80040000, max 1 CPUs
mpic: ISU size: 8, shift: 3, mask: 7
mpic: Initializing for 24 sources
PID hash table entries: 512 (order: 9, 2048 bytes)
clocksource: timebase mult[7afe256] shift[22] registered
Console: colour dummy device 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 125708k/131072k available (3736k kernel code, 5208k reserved, 184k data, 103k bss, 188k init)
Kernel virtual memory layout:
* 0xffffe000..0xfffff000 : fixmap
* 0xfd3f5000..0xfe000000 : early ioremap
* 0xc9000000..0xfd3f5000 : vmalloc & ioremap
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 64.92 BogoMIPS (lpj=324608)
Mount-cache hash table entries: 512
net_namespace: 948 bytes
NET: Registered protocol family 16
PCI: Probing PCI hardware
pci 0000:00:0e.0: PME# supported from D0 D1 D2 D3hot
pci 0000:00:0e.0: PME# disabled
pci 0000:00:0e.1: PME# supported from D0 D1 D2 D3hot
pci 0000:00:0e.1: PME# disabled
pci 0000:00:0e.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:0e.2: PME# disabled
bio: create slab at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 245
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x80004500 (irq = 21) is a 16550A
serial8250.0: ttyS1 at MMIO 0x80004600 (irq = 22) is a 16550A
console handover: boot [udbg0] -> real [ttyS1]
brd: module loaded
loop: module loaded
Driver 'sd' needs updating - please use bus_type methods
sata_sil 0000:00:0c.0: Applying R_ERR on DMA activate FIS errata fix
scsi0 : sata_sil
scsi1 : sata_sil
ata1: SATA max UDMA/100 mmio m512@0xbffffc00 tf 0xbffffc80 irq 18
ata2: SATA max UDMA/100 mmio m512@0xbffffc00 tf 0xbffffcc0 irq 18
sata_sil 0000:00:0d.0: Applying R_ERR on DMA activate FIS errata fix
scsi2 : sata_sil
scsi3 : sata_sil
ata3: SATA max UDMA/100 mmio m512@0xbffffa00 tf 0xbffffa80 irq 19
ata4: SATA max UDMA/100 mmio m512@0xbffffa00 tf 0xbffffac0 irq 19
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:00:0b.0: no PCI Express capability
eth0: RTL8110s at 0xc901cf00, 00:16:01:96:44:68, XID 04000000 IRQ 17
console [netcon0] enabled
netconsole: network logging started
ffc00000.flash: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
Creating 4 MTD partitions on "ffc00000.flash":
0x000000000000-0x000000300000 : "Linux(kernel + initrd + dtb)"
0x000000300000-0x000000360000 : "U-Boot"
0x000000360000-0x000000370000 : "U-Boot params"
0x000000370000-0x000000400000 : "unused"
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:0e.2: EHCI Host Controller
ehci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0e.2: Enabling legacy PCI PM
ehci_hcd 0000:00:0e.2: irq 20, io mem 0xbfffcf00
ehci_hcd 0000:00:0e.2: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:0e.0: OHCI Host Controller
ohci_hcd 0000:00:0e.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0e.0: irq 20, io mem 0xbfffe000
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3: SATA link down (SStatus 0 SControl 310)
ata1.00: ATA-7: SAMSUNG HD250HJ, FH100-05, max UDMA7
ata1.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD250HJ FH10 PQ: 0 ANSI: 5
usb usb2: configuration #1 chosen from 1 choice
sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:<5>sd 0:0:0:0: Attached scsi generic sg0 type 0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ohci_hcd 0000:00:0e.1: OHCI Host Controller
ohci_hcd 0000:00:0e.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:0e.1: irq 20, io mem 0xbfffd000
sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI disk
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.4.3:USB FTDI Serial Converters Driver
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
rtc-rs5c372 0-0032: rs5c372a found, 24hr, driver version 0.6
rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
MICON V2 (C) BUFFALO INC. V.1.00 installed.
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc-rs5c372 0-0032: setting system clock to 2005-12-30 09:32:46 UTC (1135935166)
ata2: SATA link down (SStatus 0 SControl 310)
ata4: SATA link down (SStatus 0 SControl 310)
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with writeback data mode.
VFS: Mounted root (ext3 filesystem) readonly on device 8:2.
Freeing unused kernel memory: 188k init
INIT: version 2.86 booting
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...done.
Setting the system clock.
Activating swap...Adding 1999992k swap on /dev/sda3. Priority:-1 extents:1 across:1999992k
done.
Checking root file system...fsck 1.41.3 (12-Oct-2008)
/dev/sda2: clean, 31385/312624 files, 158437/1250000 blocks
done.
EXT3 FS on sda2, internal journal
Setting the system clock.
Cleaning up ifupdown....
Loading kernel modules...done.
Checking file systems...fsck 1.41.3 (12-Oct-2008)
/dev/sda1: clean, 15/125416 files, 162987/499713 blocks
done.
Setting kernel variables (/etc/sysctl.conf)...done.
Mounting local filesystems...kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
done.
Activating swapfile swap...done.
Setting up networking....
Configuring network interfaces...Internet Systems Consortium DHCP Client V3.1.1
Copyright 2004-2008 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/
r8169: eth0: link up
Listening on LPF/eth0/00:16:01:96:44:68
Sending on LPF/eth0/00:16:01:96:44:68
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7
DHCPOFFER from 192.168.2.39
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPACK from 192.168.2.39
bound to 192.168.2.51 -- renewal in 8102 seconds.
done.
INIT: Entering runlevel: 2
Starting enhanced syslogd: rsyslogd.
Starting Samba daemons: nmbd smbdNET: Registered protocol family 10
lo: Disabled Privacy Extensions
.
Starting periodic command scheduler: crond.
Starting web server: apache2apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.1.1 for ServerName
.
Starting BUFFALO application
Debian GNU/Linux 5.0 KURO-NAS-T4 ttyS1
KURO-NAS-T4 login:
|
|
← U-Boot |
ハックの記録 LinkStation／玄箱 をハックしよう |
→ うるさい / noisy |
