|
LS-QL は、
HDD が４台入るし、Lenny は動くし、シリアルコンソールは動くし、何よりコンパクト。
KURO-NAS/X4 はいよいよ存在価値がなくなった。
ブートの様子。
Orion1 CPU = Low Checking DATA BUS Checking ADDRESS BUS > Checking hardware info ... === CPU-ID : 0x00005182 === === Strap status : 0x00801030 === === H/W boardId : 0x2b === === boardId : 0x1f === === micon_support: off === > OK. === BUFFALO LS-QL/R5 U-Boot. === ** LOADER ** ** BUFFALO BOARD: BUFFALO_BOARD_LS_QL_R5 LE (CFG_ENV_ADDR=fffff000) U-Boot 1.1.1 (Sep 8 2008 - 15:19:00) Marvell version: 1.12.1 - TINY Buffalo Version: 1.24-1.00 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB [256kB@fffc0000] Flash: 256 kB Addresses 20M - 0M are saved for the U-Boot usage. Mem malloc Initialization (20M - 16M): Done Soc: 88F5182 A2 CPU: ARM926 (Rev 0) running @ 400Mhz Orion 1 streaming disabled SysClock = 200Mhz , TClock = 166Mhz USB 0: host mode Net: egiga0 [PRIME] Using 88E1118 phy Marvell Serial ATA Adapter Integrated Sata device found found port multi device 0 PM found buffalo_change_power_status > Read 0x5c buffalo_IsStopAtUbootStatus > MagicKey=0x5c buffalo_change_power_status > Read 0x5c buffalo_change_power_status > Read 0x5c buffalo_change_power_status > Writing 0x5c Please Press HDD power button to continue ...
buffalo_change_power_status > Read 0x5c
buffalo_change_power_status > Writing 0x3a
HDD1 Power ON
HDD2 Power ON
HDD3 Power ON
HDD4 Power ON
Marvell Serial ATA Adapter
Integrated Sata device found
Port Multiplier found @ 0 0. Vendor: 11ab ports: 4
Device 0 @ 0 0 0:
Model: SAMSUNG HD103UJ Firm: 1AA01114 Ser#: S1B9J9AQC00304
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
Using device ide0, partition 1
Loading from block device ide device 0, partition 1: Name: hda1
Type: U-Boot File:/uImage.buffalo
2115612 bytes read
Image Name: Linux-2.6.22.7
Created: 2009-01-29 0:56:50 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2115548 Bytes = 2 MB
Load Address: 00008000
Entry Point: 00008000
Using device ide0, partition 1
Loading from block device ide device 0, partition 1: Name: hda1
Type: U-Boot File:/initrd.buffalo
7050134 bytes read
Image Name: initrd
Created: 2009-01-29 0:57:24 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 7050070 Bytes = 6.7 MB
Load Address: 00000000
Entry Point: 00000000
Using device ide1, partition 1
** Bad partition 1 **
serch_boot_drv (194)>No kernel_file 1
Using device ide1, partition 1
** Bad partition 1 **
serch_boot_drv (249)>No init_file 1
Using device ide2, partition 1
** Bad partition 1 **
serch_boot_drv (194)>No kernel_file 2
Using device ide2, partition 1
** Bad partition 1 **
serch_boot_drv (249)>No init_file 2
Using device ide3, partition 1
** Bad partition 1 **
serch_boot_drv (194)>No kernel_file 3
Using device ide3, partition 1
** Bad partition 1 **
serch_boot_drv (249)>No init_file 3
Booting from Device 0
hit any key to switch tftp boot.
Hit any key to stop autoboot: 0
Hit any key to stop autoboot: 0
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
Port Multiplier found @ 0 0. Vendor: 11ab ports: 4
Device 0 @ 0 0 0:
Model: SAMSUNG HD103UJ Firm: 1AA01114 Ser#: S1B9J9AQC00304
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
Using device ide0, partition 1
Loading from block device ide device 0, partition 1: Name: hda1
Type: U-Boot File:/uImage.buffalo
2115612 bytes read
Using device ide1, partition 1
** Bad partition 1 **
## Booting image at 00100000 ...
Image Name: Linux-2.6.22.7
Created: 2009-01-29 0:56:50 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2115548 Bytes = 2 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00800000 ...
Image Name: initrd
Created: 2009-01-29 0:57:24 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 7050070 Bytes = 6.7 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
arg:console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,32M panic=5 func=0 BOOTVER=1.24
CONFIG_BUFFALO_PLATFORM ---
Uncompressing Linux..................................................................................................................................... done, booting the kernel.
Linux version 2.6.22.7 (root@I.You) (gcc version 4.2.0 20070413 (prerelease)) #51 Thu Jan 29 09:56:43 JST 2009
CPU: ARM926EJ-S [41069260] revision 0 (ARMv5TEJ), cr=a0053177
Machine: Feroceon
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Built 1 zonelists. Total pages: 32512
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,32M panic=5 func=0 BOOTVER=1.24
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 92728KB available (3828K code, 294K data, 120K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
env_format_version = 0x00000006
product_id = 0x00004000
Sys Clk = 200000000, Tclk = 166664740
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 128MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
PCI0_MEM ....base e8000000, size 128MB
PCI0_IO ....base f2100000, size 1MB
INTER_REGS ....base f1000000, size 1MB
DEVICE_CS0 ....no such
DEVICE_CS1 ....base f4000000, size 32MB
DEVICE_CS2 ....no such
DEV_BOOCS ....base ff800000, size 8MB
CRYPT_ENG ....base f0000000, size 64KB
Marvell Development Board (LSP Version 3.0.5_NAS_GDP_p8)-- BUFFALO_BOARD Soc: 88F5182 A2
Detected Tclk 166664740 and SysClk 200000000
Marvell USB EHCI Host controller #0: c055b600
Marvell USB EHCI Host controller #1: c055b400
IO Request resource failed - Pci If 0
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
NET: Registered protocol family 2
Time: orion_clocksource clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 32768K
RTC registered
mvCesaInit: sessions=640, queue=64, pSram=f0000000
Use the XOR engines (acceleration) for enhancing the following functions:
o RAID 5 Xor calculation
o kernel memcpy
o kenrel memzero
o copy user to/from kernel buffers
Number of XOR engines to use: 2
Use IDMA channels 2 and 3 for enhancing the following function:
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SGI XFS with ACLs, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
io scheduler noop registered (default)
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A
serial8250.0: ttyS2 at MMIO 0xf1012100 (irq = 4) is a 16550A
RAMDISK driver initialized: 3 RAM disks of 32768K size 1024 blocksize
loop: module loaded
Marvell Ethernet Driver 'mv_ethernet':
o Uncached descriptors in DRAM
o DRAM SW cache-coherency
o TCP segmentation offload enabled
o Checksum offload enabled
o Rx desc: 128
o Tx desc: 256
o Loading network interface ** eth_init_module (0)
'eth0'
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
scsi 0:0:0:0: Direct-Access SAMSUNG HD103UJ 1AA0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sda: sda1 sda2 sda4 < sda5 sda6 >
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
physmap platform flash device: 01000000 at f0000000
physmap-flash physmap-flash.0: map_probe failed
Found: SST 39LF020
cfi_flash_0: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
mice: PS/2 mouse device common for all mice
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid6: int32x1 21 MB/s
raid6: int32x2 28 MB/s
raid6: int32x4 35 MB/s
raid6: int32x8 31 MB/s
raid6: using algorithm int32x4 (35 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: measuring checksumming speed
arm4regs : 304.000 MB/sec
8regs : 249.200 MB/sec
32regs : 270.800 MB/sec
raid5: using function: arm4regs (304.000 MB/sec)
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Buffalo CPU Inerupts Driver (C) BUFFALO INC. Ver.0.01 alpha1 installed.
Buffalo Gpio Control Driver (C) BUFFALO INC. Ver.0.02 installed.
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
---- in linuxrc ---
Version 1.00 2008/ 7/ 1
grep: /var/tmp/devlink: No such file or directory
Sun Mar 8 00:49:39 JST 2009
CheckDevices
grep: /var/tmp/devlink: No such file or directory
linuxrc:choose operation (timeout 4[s])
1:RamRoot other:HddRoot ? -HddRoot-
-- rebuild mdadm.conf for BOOT, ROOTFS --
md: md10 stopped.
mdadm: /dev/diskmd: md1 stopped.
1_1 has wrong uuid.
mdadm: no devices found formd: md0 stopped.
/dev/md10
mdadm: /dev/disk1_1 has wrong uuid.
mdadm: no devices found for /demd: bind<sda1>
v/md1
raid1: raid set md0 active with 1 out of 4 mirrors
mdadm: /dev/md0 has been started with 1 drive (out of 4).
-- setup max error counts --
/sys/block/md0/md/maxerr_cnt is setted to -1
Starting :fsck_disks(boot) ... [Failed. ]
Starting :fsck_disks(rootfs) ... [Success.]
Starting :mount(boot) ... kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
[Success.]
Starting :umount(boot) ... [Success.]
-- rebuild mdadm.conf for BOOT, ROOTFS --
md: md10 stopped.
mdadm: cannot open device /dev/disk1_1: Device or resource busy
mdadm: /dev/disk1_1 has wrong uuid.
mdadm: /dev/disk1_2 has wrmd: bind<sda5>
ong uuid.
raid1: raid set md10 active with 1 out of 4 mirrors
mdadm: /dev/md10md: md1 stopped.
has been started with 1 drive (out of 4).
md: bind<sda2>
raid1: raid set md1 active with 1 out of 4 mirrors
mdadm: /dev/md1 has been started with 1 drive (out of 4).
-- setup max error counts --
/sys/block/md0/md/maxerr_cnt is setted to -1
/sys/block/md1/md/maxerr_cnt is setted to -1
/sys/block/md10/md/maxerr_cnt is setted to -1
Filesystem "md1": Disabling barriers, not supported by the underlying device
XFS mounting filesystem md1
PRODUCTID=0x00004000 PRODUCTID=0x00000000
-- CopyFromInitrdToHdd --
.........Finish
umount: cannot open /proc/mounts
Filesystem "md1": Disabling barriers, not supported by the underlying device
XFS mounting filesystem md1
VFS: Mounted root (xfs filesystem).
Trying to move old root to /initrd ... okay
Freeing init memory: 120K
init started: BusyBox v1.7.0 (2007-10-15 19:49:46 IST)
starting pid 511, tty '': '/etc/init.d/rcS'
--- rcStart (hddroot) ---
Sun Mar 8 00:49:48 JST 2009
** step1 **
=== checkroot.sh ===
grep: /var/tmp/devlink: No such file or directory
Filesystem "md1": Disabling barriers, not supported by the underlying device
mount: mounting /dev/root on / failed: No such file or directory
ln: /var/spool/cron/cron: File exists
grep: /var/tmp/devlink: No such file or directory
Adding 1003896k swap on /dev/md10. Priority:-1 extents:1 across:1003896k
=== procps.sh ===
=== devpts.sh ===
=== sethostname.sh ===
configure files from Buffalo parameters.
=== restore_config.sh ===
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Update configuration files
Restore previous configuration files
delete unnecessary samba lock files on /tmp/upconfig//etc/samba/lock...
=== free_ramdisk.sh ===
Successfully unmounted /dev/ram0
Successfully unmounted /dev/ram0
=== vm_tune.sh ===
start
Starting HTTPD services: /usr/local/apache/bin/apachectl start: httpd started
** step2 **
=== EnablingAutoip.sh ===
=== usb.sh ===
/sbin/hotplug [module]
/sbin/hotplug [drivers]
usbcore: registered new interface driver usbfs
/sbin/hotplug [drivers]
usbcore: registered new interface driver hub
/sbin/hotplug [drivers]
usbcore: registered new device driver usb
/sbin/hotplug [module]
/sbin/hotplug [drivers]
ehci_marvell ehci_marvell.4523: Marvell Orion EHCI
/sbin/hotplug [usb_host]
ehci_marvell ehci_marvell.4523: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.4523: irq 17, io base 0xf1050100
ehci_marvell ehci_marvell.4523: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
/sbin/hotplug [usb]
/sbin/hotplug [usb_endpoint]
usb usb1: configuration #1 chosen from 1 choice
/sbin/hotplug [usb]
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
/sbin/hotplug [usb_endpoint]
/sbin/hotplug [usb_device]
ehci_marvell ehci_marvell.167817: Marvell Orion EHCI
/sbin/hotplug [usb_host]
ehci_marvell ehci_marvell.167817: new USB bus registered, assigned bus number 2
[/etc/hotplug.d/usb_device/buffalo.hotplug] usb_device
ehci_marvell ehci_marvell.167817: irq 12, io base 0xf10a0100
ehci_marvell ehci_marvell.167817: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
/sbin/hotplug [usb]
/sbin/hotplug [usb_endpoint]
usb usb2: configuration #1 chosen from 1 choice
/sbin/hotplug [usb]
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
/sbin/hotplug [usb_endpoint]
/sbin/hotplug [usb_device]
/sbin/hotplug [module]
USB Universal Host Controller Interface driver v3.0
/sbin/hotplug [drivers]
/sbin/hotplug [module]
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
/sbin/hotplug [drivers]
/sbin/hotplug [module]
/sbin/hotplug [drivers]
/sbin/hotplug [drivers]
/sbin/hotplug [module]
/sbin/hotplug [drivers]
[/etc/hotplug.d/usb_device/buffalo.hotplug] usb_device
=== hotplug.sh ===
*** /usr/local/bin/DirectCopy_wait.sh [stop]
cat: can't open '/var/run/DirectCopy_wait.pid': No such file or directory
kill: usage: kill [-s sigspec | -n signum | -sigspec] pid | jobspec ... or kill -l [sigspec]
=== networking.sh ===
create network files..
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
killall: dhcpcd: no process killed
route: SIOCDELRT: No such process
Configuration network interface: lo eth0
requesting DHCP tout=30[s]
networking.sh: dhcp requesting...
DontDownIfaceeth reg(9) val=0x0300
eth0: link down
alwaysFork
eth0: link up, full duplex, speed 1 Gbps
sendto: count 6 sync 1
sendto: count 5 sync 0
dhcpcd.exe: interface eth0 has been configured with old IP=192.168.2.50 GATEWAY=192.168.2.1
** networking.sh dhcp fin.
configure files from Buffalo parameters.
=== syslog.sh ===
Starting system logger:
Starting kernel logger:
=== network_control.sh ===
=== inetd.sh ===
Starting inetd:=== errormon.sh ===
Starting errormon:errormon ver.1.01(BuildDate Jan 22 2009 09:18:20 compiled for BUFFALO NAS Series) Started
=== kernelmon.sh ===
Starting kernelmon:=== miconmon.sh ===
=== checkSysMd.sh ===
KERNELMOn (lanact 0 half)
/dev/md0
Raid Level : raid1
KERNELMOn (lanact 1000 full)
/dev/md1
Raid Level : raid1
/dev/md10
Raid Level : raid1
=== start_data_array.sh ===
-- start data arrays --
-- setup max error counts --
/sys/block/md2/md/maxerr_cnt is setted to -1
/usr/local/lib/libmd: line 262: /sys/block/md2/md/maxerr_cnt: No such file or directory
/sys/block/md3/md/maxerr_cnt is setted to -1
/usr/local/lib/libmd: line 262: /sys/block/md3/md/maxerr_cnt: No such file or directory
/sys/block/md4/md/maxerr_cnt is setted to -1
/usr/local/lib/libmd: line 262: /sys/block/md4/md/maxerr_cnt: No such file or directory
-- check /etc/melco/diskinfo and real RAID disks. --
RAID is not normal. rebuild /etc/melco/diskinfo file.
mdadm: No arrays found in config file
-- Mount local disks --
XFS mounting filesystem sda6
** spool array1
** spool disk1
** share disk1
** mt-daapd disk1
** step3 **
=== diskmon.sh ===
=== drivecheck.sh ===
=== ftpd.sh ===
ftp is OFF
=== atalk.sh ===
atalk is OFF
=== httpd.sh ===
start
Starting HTTPD services: /usr/local/apache/bin/apachectl start: httpd (pid 870) already running
=== smb.sh ===
configure samba
LoadConfFileString:key=[local_auth] not found in /etc/melco/info.
load_info ItemValue = off
LoadConfFileString:key=[ad_dns] not found in /etc/melco/info.
LoadConfFileOnOff:key=[info_visible] not found in /etc/melco/info.
LoadConfFileString:key=[msdfs_link1_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link2_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link3_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link4_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link5_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link6_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link7_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link8_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link9_name] not found in /etc/melco/msdfs.
file:/etc/samba/smb.conf
>IconvCodeCharset CodePage=0,charset=CP932
buf=array1=off
buf=array2=off
buf=disk1=normal
GetSpoolDirectory> returning devicename [/mnt/disk1]
file:/etc/pam_smb.conf
Setting up msdfs symbolic links... [Failed ]
Starting SMB services:
Starting NMB services:
=== clientUtil_servd.sh ===
Starting clientUtil_server:starting on eth0
=== bonjour.sh ===
Starting Bonjour services: done
=== lsprcvd.sh ===
Starting lsprcvd:=== daemonwatch.sh ===
Starting daemonwatch:daemonwatch Ver.1.01
watch list file : /etc/daemonwatch.list
=== cron.sh ===
Start services: crondlogrotate state -- version 2
=== checkconfig.sh ===
=== ups.sh ===
err:
err:
=== pwrmgr.sh ===
Starting pwrmgr:
Shutting down pwrmgr:
Starting pwrmgr:
** step4 **
=== modules.sh ===
Starting module subsystem ...
Starting module webaxs ... [Success.]
=== itunes.sh ===
=== lprng.sh ===
clearing printer queue
Printer 'lp@localhost' - cannot open connection - No such file or directory
Make sure the remote host supports the LPD protocol
Printer 'lp-ps@localhost' - cannot open connection - No such file or directory
Make sure the remote host supports the LPD protocol
/mnt/disk1/spool/samba created
/mnt/disk1/spool/lp created
Start services: lpd
=== ltbootd.sh ===
Starting services: rarpd tftpd rarpcfgd fwupdated.
=== pmcd.sh ===
=== webaxs.sh ===
WebAccess is OFF
=== twonky.sh ===
=== bittorrent.sh ===
bittorrent is off
/etc/init.d/rcS: line 102: /etc/rc.d/extensions.d/S*: No such file or directory
=== bootcomplete.sh ===
** step final(after bootcomplete) **
=== hdd_late_check.sh ===
No need to check hdd(hdd is fine).
No new disks.
=== check_initialization.sh ===
bootarg "func" is disabled.
=== usb_late_check.sh ===
starting pid 2473, tty '': '/sbin/getty'
nothing to delete
*** /usr/local/bin/DirectCopy_wait.sh [start]
BUFFALO INC. LinkStation series
LS-QL233 login: 1 USB_DEVICE=none
2 USB_DEVICE=none
3 USB_DEVICE=none
4 USB_DEVICE=none
5 USB_DEVICE=none
KERNELMOn (PSW_on)
Shutting down pwrmgr:
BUFFALO INC. LinkStation series LS-QL233 login: root No mail. root@LS-QL233:~#
root@LS-QL233:~# KERNELMOn (PSW_short_pushed) KERNELMOn (PSW_pushed) CPU_STAT=normal_state ##### shutdown start starting pid 3124, tty '': '/etc/init.d/rcDown' --- rcDown --- ===== exec:shutdown_start.sh ===== called shutdown_start /etc/init.d/shutdown_start.sh err: ===== exec:shutdown_proc.sh ===== Save current configuration files delete unnecessary samba lock files on //etc/samba/lock... tar: Removing leading `/' from member names tar: Removing leading `/' from member names Stop daemonwatch:done. Stop logchkd:killall: logchkd: no process killed done. Stop lsprcvd:Stop services: crondStop inetd:done. Stop errormon:done. Stop clientUtil_server:rm: cannot remove '/var/run/clientUtil_server-eth0.pid': No such file or directory Message from syslogd@LS-QL233 at Sun Mar 8 00:51:31 2009 ... LS-QL233 clientUtil_server[1876]: ap_serv_exit() exit ap_servd. code=15 Shutting down FTPD services: killall: proftpd: no process killed Shutting down SMB services: Shutting down NMB services: Cleanup msdfs symbolic links... [Success] Shutting down WINBIND services: killall: winbindd: no process killed Shutting down PAMSMBD services: killall: pamsmbd: no process killed Stop servecies: atalkd afpd /sbin/hotplug [module] /sbin/hotplug [module] /sbin/hotplug [module] NET: Registered protocol family 5 Can't unregister LS-QL233:Workstation@* Can't unregister LS-QL233:netatalk@* killall: atalkd: no process killed killall: afpd: no process killed killall: papd: no process killed Starting Bonjour services: done stop Shutting down HTTPD services: /usr/local/apache/bin/apachectl stop: httpd stopped killall: speedy: no process killed killall: speedy_backend: no process killed Deconfiguration network interface: lo eth0 killall: diskmon_exec.sh: no process killed Stop kernelmon:killall: /proc/buffalo/kernevnt: no process killed done. Stopping module subsystem ... Shutting down webaxs ... [Failed. ] clearing printer queue Printer lp@LS-QL233: Printer lp-ps@LS-QL233: Stop services: lpd clearing printer queue Printer 'lp@localhost' - cannot open connection - Connection refused Make sure the remote host supports the LPD protocol Printer 'lp-ps@localhost' - cannot open connection - Connection refused Make sure the remote host supports the LPD protocol Stop services: rarpd tftpd rarpcfgd fwupdated. killall: miconmon_exec.sh: no process killed Stop errormon:done. cat: can't open '/var/run/pmcd.pid': No such file or directory kill: usage: kill [-s sigspec | -n signum | -sigspec] pid | jobspec ... or kill -l [sigspec] killall: pmcd_exec.sh: no process killed killall: apcupsd: no process killed killall: omronupsd: no process killed Shutting down kernel logger: Shutting down system logger: ===== exec:umount_disk.sh ===== \n==== unmounting all disks ==== umount: forced umount of /mnt/usbdisk1 failed! umount: cannot umount /mnt/usbdisk1: Invalid argument umount: forced umount of /mnt/usbdisk2 failed! umount: cannot umount /mnt/usbdisk2: Invalid argument umount: forced umount of /mnt/disk2 failed! umount: cannot umount /mnt/disk2: Invalid argument umount: forced umount of /mnt/disk3 failed! umount: cannot umount /mnt/disk3: Invalid argument umount: forced umount of /mnt/disk4 failed! umount: cannot umount /mnt/disk4: Invalid argument umount: forced umount of /mnt/array1 failed! umount: cannot umount /mnt/array1: Invalid argument umount: forced umount of /mnt/array2 failed! umount: cannot umount /mnt/array2: Invalid argument umount: forced umount of /mnt/usbdisk1 failed! umount: cannot umount /mnt/usbdisk1: Invalid argument umount: forced umount of /mnt/usbdisk2 failed! umount: cannot umount /mnt/usbdisk2: Invalid argument ===== exec:start_data_array.sh ===== umount: forced umount of /mnt/array1 failed! umount: cannot umount /mnt/array1: Invalid argument umount: forced umount of /mnt/array2 failed! umount: cannot umount /mnt/array2: Invalid argument /sbin/hotplug [block] md: md2 stopped. mdadm: stopped /dev/md2 ===== exec:sendsigs.sh ===== umount: cannot umount /proc: Device or resource busy starting pid 3795, tty '': '/bin/umount' The system is going down NOW! Sending SIGTERM to all processes Sending SIGKILLmd: md1 in immediate safe mode to all processemd: md0 in immediate safe mode md: md10 in immediate safe mode Requesting system halt md: stopping all md devices. md: md1 still in use. md: md10 switched to read-only mode. md: md0 switched to read-only mode. sd 0:0:0:0: [sda] Synchronizing SCSI cache System halted. BuffaloChangePowerStatusBeforeHalt > Check power status. MagicKey = 0x02 BuffaloChangePowerStatusBeforeHalt > Changed to 0x7a from 0x02 Orion1 CPU = Low Checking DATA BUS Checking ADDRESS BUS > Checking hardware info ... === CPU-ID : 0x00005182 === === Strap status : 0x00801030 === === H/W boardId : 0x2b === === boardId : 0x1f === === micon_support: off === > OK. === BUFFALO LS-QL/R5 U-Boot. === ** LOADER ** ** BUFFALO BOARD: BUFFALO_BOARD_LS_QL_R5 LE (CFG_ENV_ADDR=fffff000) U-Boot 1.1.1 (Sep 8 2008 - 15:19:00) Marvell version: 1.12.1 - TINY Buffalo Version: 1.24-1.00 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB [256kB@fffc0000] Flash: 256 kB Addresses 20M - 0M are saved for the U-Boot usage. Mem malloc Initialization (20M - 16M): Done Soc: 88F5182 A2 CPU: ARM926 (Rev 0) running @ 400Mhz Orion 1 streaming disabled SysClock = 200Mhz , TClock = 166Mhz USB 0: host mode Net: egiga0 [PRIME] Using 88E1118 phy Marvell Serial ATA Adapter Integrated Sata device found found port multi device 0 PM found buffalo_change_power_status > Read 0x7a buffalo_IsStopAtUbootStatus > MagicKey=0x7a buffalo_change_power_status > Read 0x7a buffalo_change_power_status > Read 0x7a buffalo_change_power_status > Writing 0x5c Please Press HDD power button to continue ...
|
|
← シリアルコンソール / Serial Console |
ハックの記録 LinkStation／玄箱 をハックしよう |
→ LS-QLシリーズファームウェア アップデータ Ver.1.07β |
