WD3200SD

京都駅南のショップで S-ATA HDD を買ってきた。
I bought the Serial ATA hard drive in the PC shop near the Kyoto station.

Complaint to the shop.

玄箱/Pro が入荷したという電話はもらっていないが、念のため聞いてみたら、、、
案の定入荷していた。注文品が入荷しても連絡くれなかったのは、Clie, 玄箱/HG に続いてこれでもう３回目。

ソフマップ京都店は、注文した商品が入荷しても絶対に連絡をくれません。
ソフマップ京都店に商品を注文するのはやめた方が良いでしょう

LS-GL を使って、パーティションを削除する。
Connect the hard drive to LS-GL and remove all partitions.

ude:~# fdisk /dev/sdb
Device contains neither a valid DOS partition table, nor Sun, SGI or OSF disklabel
Building a new DOS disklabel. Changes will remain in memory only,
until you decide to write them. After that, of course, the previous
content won't be recoverable.


The number of cylinders for this disk is set to 38913.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
   (e.g., DOS FDISK, OS/2 FDISK)
Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite)

               :
               :
               :
Command (m for help): p

Disk /dev/sdb: 320.0 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot      Start         End      Blocks   Id  System

Command (m for help): w
The partition table has been altered!

Calling ioctl() to re-read partition table.
Syncing disks.
ude:~#

解説書 No.5, No.6, No.7 の手順で HDD をセットする。
Set the hard drive into the KURO-BOX/Pro.

電源投入。
Turn on

Orion1   CPU =  Low

=== KURO U-Boot. ===
 ** LOADER **
 ** KUROBOX BOARD: KURO_BOX  LE (CFG_ENV_ADDR=fffff000)
               :
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
  Vendor: WDC       Model: WD3200SD-01KNB0   Rev: 08.0
  Type:   Direct-Access                      ANSI SCSI revision: 03
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
 sda:
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 0
              :
===== Starting mount_share.sh =====
Mounting /dev/sda on /mnt/disk1 as a xfs file system.
XFS: bad magic number
XFS: SB validate failed
mount: mounting /dev/sda on /mnt/disk1 failed
Failed.
Mounting /dev/sda on /mnt/disk1 as a ext3 file system.
mount: mounting /dev/sda on /mnt/disk1 failed
Failed.
              :

KUROUTOSHIKOU KUROBOX Series KUROBOX/PRO(KOSHO)
KUROBOX-PRO login:

xfs と ext3 でマウントを試みているようだ。この状態ではまだ使えない
It tried to mount the hard drive as xfs, and as ext3. I can NOT use it yet.

KURO-BOX/PRO

玄人志向
楽天市場
TSUKUMO ネットショップ
Yahoo!ショッピング
Sofmap
クレバリー
TwoTop

SCON-KIT/PRO

玄人志向
TSUKUMO ネットショップ
Yahoo! ショッピング
パソＱ
ValuMore
uWorks

玄箱PROをハックしよう

ASCII
楽天ブックス
Amazon
cbook24
e-hon
JBook
BK1
livedoorブックス
紀伊國屋書店BookWeb

←
共有フォルダ／shared folder

ハックの記録
LinkStation／玄箱をハックしよう

→
HDD のセットアップ/Setup the hard drive